297462-1-S-GE-WR29X5171         -Icemaker Switch
297462-1-S-GE-WR29X5171         -Icemaker Switch 297462-2-S-GE-WR29X5171         -Icemaker Switch 297462-3-S-GE-WR29X5171         -Icemaker Switch

Icemaker Switch

PartSelect Number PS297462

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $20.51
  • You Save

    $3.42
  • Your Price

    $17.09
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 3 reviews What's this?
1-3 of 3
 

11 of 12 people found this instruction helpful

Parts Used

  • Icemaker Switch

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerJames from Mebane NC

Ice maker would not make ice..

1) I removed the icemaker and placed on work table.
2) I pried the front plastic cover from the control box to expose the front base.
3) I removed the three mounting screws from the base (it is not necessary to remove the screw in the plastic gear) and removed the front base. This exposed the back base
4) Using an ohmmeter, I was able to isolate a bad contact on one of the three microswitches in the control box (the one that was mounted to the back base). Replacing this microswitch solved the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerAlice from Cookson OK

Ice maker overflows bucket and waterline leak

What can I tell you to help except if the 75+ year old Grandma can do it you can do it also. This site was great and the shipping was super fast.

Have put up with an ice maker that never automatically quit making ice for over a year. I just manually shut it off (remembered some of the time and was reminded by the error messages when overflowing at other times). I just didn't want to pay for a service call and all that involves for this item. Then the incoming waterline split and I had to make a decision and that was to DIY the repair after reading the info on this site. The ice maker was a breeze and you can read the details in other posts. Here I will say it takes removing two screws to loosen (mine wouldn't slip off unless screws were totally removed), (I shut off the water and unplugged refrigerator since I am neither an electrician nor an appliance repairman) unplugging the ice maker by removing one hex head, removing the control cover (bottom to top as described in other posts), remove 3 screws only in the metal plate that holds the inside of the ice maker together to get access to the "brains", replaced the Cam, reverse to reassemble (remembering to get the arm back into it's hole in the metal plate. End of that job.

After reading posts about the the water line tubing, I made sure that I had all of the parts of the correct size to replace all of the tubing that passes by the compressor. I did not, however, replace the full length of any of the tubing. I cut off the bad sections of the 1/4" to the middle of the back of the refrigerator and connected a new section with the 1/4" x 1/4" water tube unions.(I was able to buy 1/4" water line, 5/16" water line and 1/4" x 1/4" water tube unions locally but I could not find 5/16" x 5/16" water tube unions so I ordered them from PartSelect at the same time as I ordered the ice maker cam.)

Then I went to the inside of the refrigerator removed the cover from the water reservoir (behind the hydrator), cut out the old section of the water dispenser lines that pass by the compressor, threaded in (not as easy as the outside tubes but not difficult either) the new tubing and connected with the 5/16" x 5/16" water tube unions. You will get lots more details in other posts but this is to tell you that you CAN DO IT with help from this site! I fixed it all for less than $20 (versus cost of new refrigerator, or new ice maker, or service call).

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerJack from Bloomington IL

Ice maker would not shut off

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3