297369-2-S-GE-WR29X160          -Icemaker Stripper
297369-2-S-GE-WR29X160          -Icemaker Stripper 297369-1-S-GE-WR29X160          -Icemaker Stripper

Icemaker Stripper

PartSelect Number PS297369

This part strips the ice from the icemaker mold during the ejection cycle.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Compare At

    $24.11
  • You Save

    $4.02
  • Your Price

    $20.09
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Icemaker Stripper Arm

Part Number 2354686

This part strips the ice from the icemaker mold during the ejection cycle. Used on rear mount icemakers.

Order within the next 3 hrs and your part ships today!
$27.98
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 4 reviews What's this?
1-4 of 4
 

17 of 20 people found this instruction helpful

Parts Used

  • Icemaker Stripper

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerTracy from Yuba City CA

Stripper on the icemaker broke into pieces.

Remove the two nuts holding the top of the unit to the side of the freezer using a 1/4 in nutdriver. Pull the unit out and unplug it from the back of the freezer. Remove all pieces of the broken stripper. The replacement part fits onto a peg on the back of the icemaker and into a slot. Bend into place and slide into position.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Icemaker Stripper

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerErnest W. from Charlotte NC

Ice maker stripper lost a tooth

First turn off the power, remove the ice tray, remove the two screws holding the ice maker to the side of the freezer, use the screw driver to gently open the electrical clip for the power cord inside the freezer, remove the complete unit from freezer, bend the old stripper from the holding pin- it is flexible- it will bend, replace the new stripper on the holding pin and bend into the slot to hold it firmly, no water will come out from the fill cup into the freezer, plug in the power cord, mount back to side of freezer, you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker Stripper

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerTed from Harrisonburg VA

Icemaker stripper fall a part

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Icemaker Stripper

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerMarie from Elk Grove Village IL

My ice breaker started leaking and making noise anf the stripper broke.

I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4