285067-1-S-GE-WR02X10647        -Sensor Grille
285067-1-S-GE-WR02X10647        -Sensor Grille 285067-2-S-GE-WR02X10647        -Sensor Grille

Sensor Grille

PartSelect Number PS285067

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $4.51
  • You Save

    $.75
  • Your Price

    $3.76
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Shunt Sensor

Part Number 285088

$3.00
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 2 reviews What's this?
1-2 of 2
 

12 of 15 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

Tools

CustomerGene from The Woodlands TX

Not cooling, water in refrigerator

For several years, had problem with water accumulating in the bottom of the refrigerator...took out the "custom cool" drawer and assigned my kids the responsibility to dry it out daily after supper (about a fourth of cup of water daily)...the water was condensing and dripping down the left side of the refrigerator... NOT coming from the refregerator evaporator drip pan area. Then the refrigerator and freeezer had erratic cooling...paid 4 grand for this GE stainless steel on the front/sides frig about 5 years ago... then my wife said she wanted a new refrigerator...what the heck...went on to numerous websites and finally decided to do my own "overall"...had nothing to lose except the price of the parts. A helpful web site is the GE technician site at...www.manualinstruction.com/wp-content/uploads/2011/10/ge-sidebyside.pdf. I ordered the four thermisters, a new freezer defroster (the old one was probably OK...the freezer coils were not "iced Up"), and a new defroster thermonmeter. While I was at it, I ordered a new refrigerator evaporator drip pan that was rusting a bit. As per other instructions in this website, just spliced in the new thermisters,used wire twist caps and eletrical tape to seal them. The GE site is a bit more elaborate on the "correct" way to do this. The refrigerator evaporator coil is a bit tricky...see the above ge site...but I just cut the rubber thermister holder down the middle and then tracked the thermister through the holder and stuck it in the block and taped the holder back together...(removed the block first ) and then zip-lined the block back to the coil like it was originally. It was about 3 hours to do everything...and guess what...temp in the freezer is -5...temp in the frig is 36...and NO MORE WATER IN THE BOTTOM OF THE REFRIGERATOR, NO MORE WATER DRIPPING DOWN THE LEFT SIDE OF THE REFRIGERATOR...what will my kids do...I feel like the refrigerator guru now. Wish I had done this several years ago. The parts I ordered came in 3 days. I'm lovin my refrigerator now and my wife is lovin me. It's really easier than I thought it would be...the GE tech website has some "diagnostic" info to isolate different problems... but I just decided to replace "everything" since the parts were not that expensive and it was going to be a "do or die" on getting a new refrigerator.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 13 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerTheodore from San Gabriel CA

Refridgerator was not defrosting & so was getting warm

On the PartSelect website, I chose the 'refridgerator is too warm' problem choice. The site sugested replacing the sensors so I purchased them. The drain trough on the refrigerator side was leaking and it and the defrost thermostat were not too expensive so I bought them too.
Once the parts arrived I installed them. I had already disassembled the inside of the freezer. The sensors and thermostat had to be connected electrically. So I cut off the old parts and stripped their wires. (the new parts' wires were already stripped.) I then used wire nuts to connect the new wires to the old and stuffed the wire back into its compartment and installed its cover. The defrost Thermostat has to be clipped to the refrigeration line. So after attaching its wires I had to work it into its place.
I then reassembled the inside of the freezer and let it sit for an hour before turning it back on. Once it was turned on it seemed to work well, but after only 3 or 4 days the coils began freezing over again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-2 of 2