285013-1-S-GE-WR02X10585        -Recess Door Spring
285013-1-S-GE-WR02X10585        -Recess Door Spring 285013-2-S-GE-WR02X10585        -Recess Door Spring http://www.partselect.com/Schematics/GE/00125643i01.gif

Recess Door Spring

PartSelect Number PS285013

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door latch failure.
  • Door Sweating.
  • Ice maker won’t dispense ice.
  • Door won’t open or close.
  • Frost buildup.
  • Not dispensing water.
  • Leaking.
  • Freezer section too warm.
  • Ice maker not making ice.
  • Will Not Start.
  • Compare At

    $4.06
  • You Save

    $.68
  • Your Price

    $3.38
In Stock
Order within the next 21 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Dispenser Door Recess Crank

Part Number 291908

Order within the next 21 mins and your part ships today!
$3.39
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 38 reviews What's this?
 

15 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: danny from west potsmouth, OH

Ice auger was broke and ice was freezing in the recess door

all parts worked and were easy to install. probably saved me from having to buy a new fridge. ice maker is working fine and recess door flap is closing correctly. very satisfied.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 20 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Larry from Republican City, NE

Ice maker door failed to close letting ice melt

Removed the front panel on the door that has the ice maker controls. Removed the screws and parts. Reassembled the parts and it works better than new. Ice door closes firmly and holds tight.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Mark from Robins, IA

Ice chute flapper would not close all the way

Following the advice of others on this site, I popped out the control panel by pushing up through the 2 outer-most holes on the under-side of the panel (the middle hole is unused). I installed the new solenoid exactly as shown in the PartSelect video. The new crank, spring, and flapper installed easily as well; I did apply a little grease to the hinge points on the crank to ensure no binding. I also installed a new microswitch. The wires are best removed from the old switch with a needlenose pliers. The old switch looked like it had some grease on the switch (where it makes contact with the cup lever) so I put some grease on the new switch as well. All-in-all, very easy and the frig works like new. It's nice to hear the flapper slam shut 4 seconds after dispensing ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: mike from hatboro, PA

Flapper is stuck open

There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Leslie from Vacaville, CA

The icemaker door did not work and broke the ice maker

I replaced the door and soleniod and the other parts and it works great now

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers
Customer: OLESTER from SAN DIEGO, CA

This model is a lemon (on-line for compliants). Numerous problems

Removed 4 screws & replace parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: James from Milford, NH

Flapper movement both directions

Replacing was easy. Cleaning took the longest. Order screws with parts, I could not find them at the hardware store. I suggest a coat of oil (3 in one) on the solenoid/piston surfaces. I probably did not have to replace them. The rust was inhibiting the piston movement. Some steel wool and oil would have probably fixed it. If the flap closing starts sounding softer, I'm going to take it apart and clean it first.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Joe from Kennesaw, GA

Ice maker door leaking air causing inside to ice up.

The allan wrench pushes into the holes nder the front control plate and it pops off. Unplug the wires and set aside. Four screws removes the next piece and the "flaper" door is visable.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Joe from Clinton township, MI

Door latch broke

took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Mark from Elk Grove Vill, IL

Ice dispenser door sticking open

Removed access panel on freezer door, removed circuit board, removed and replaced solenoid, reinstalled previously removed parts

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Lake George, NY

The ice dispenser door would not open or close.

It was actually very easy. You simply remove the display cover (you just want to be careful removing the display cover so as not to damage the lower part which secures it to the door), unplug the wires, remove the inner cover (4 screws) to gain access to the solenoid. Remove the 4 screws on the solenoid replace with the new one, put the inner cover back in with the 4 screws that were previously removed, plug the wires back in and then replace the display cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: brian from Holland, OH

Ice door stuck open

The ice shute frosted up after the selonoid rusted. 1: Small flat screwdrvier to pop off control panel
2: phillips screwdriver to remove 4 screws to control backing plate.
3: Phillips screwdirver to remove seloniod and flap door.
4: replace selonoid, flap door, spring and crank door. Consider replacing screws due to rust.

I would replace all these parts at one time to save on shipping as any of them could cause the frosting. THe shipping is more than most parts! VERY EASY and QUICK!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 21 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: CHRISTOPHER from CEDAR KNOLLS, NJ

Dishwasher door would not latch

opened door removed screws holding back side of door took out front panel with latch assembley found broken part and replaced it

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Bill from Venice, FL

Ice maker dispenser chute frosting up

Before starting my repairs I checked for part suppliers online. Partselect was one of the first I saw. They also had instruction videos. After watching the video, I took apart the ice maker and found the solenoid had rusted. I replaced the solenoid and while everything was apart I replaced the crank, spring and the flapper. The entire process only took about 20 minutes and that was only because of their informative videos.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Betty from Chester, CT

When we tried the door wouldn't open and the door handle actuator fell out in our hand

Took the screws out of the inner panel to open it and expose the latch area. Found the door spring stuck to the insulation so we saved it. Used the part's list picture to figure out how to put the latch parts together (wish the picture was better). Reattached the inner panel. The latch works better now than when it was new....which makes us wonder.

Help other customers find the most helpful instructions.

Were these instructions helpful?