272183-1-S-GE-WH41X365          -Water Pressure Switch Hose
272183-1-S-GE-WH41X365          -Water Pressure Switch Hose 272183-2-S-GE-WH41X365          -Water Pressure Switch Hose

Water Pressure Switch Hose

PartSelect Number PS272183

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Leaking water.
  • Compare At

    $7.18
  • You Save

    $1.20
  • Your Price

    $5.98
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

54 of 60 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerAngie from Saint Louis MO

Washer was overflowing-- not registering that the tub was full

I replaced both the tube and the pressure switch and still no luck. turns out that i didn't need either part. the little box that the tube hooks on to at the bottom left of the tub had a clog in it. we disconnected the tube from the switch and just blew through it. the clog broke loose and my washer works again!! decided that i was leaving the new parts on the machine. one less thing to worry about in the future.... ????

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMark from Dallas NC

Water level overflowing

Unplug the appliance first! I removed the front panel and then the top panel with the lid by removing the two screws in the front and pulling up and out and unplugging the electrical connector. I then removed the 4 star screws from the top of the control section. The pressure switch is removed by pressing down on the tab and rotating it. I installed the new pressure switch and connected the three wires one at a time. I then re-routed the new hose and connected both ends. I reassembled everything and tested the new sensor by allowing the machine to fill with water. It now works properly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 14 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRobert from Riverview FL

Washing machine overflows on "cold water" setting

Repair was simple. Initially thought the problem was the Water Level pressure swith, but since water overflow was only happening when selecting cold wash & during the rinse cycle (Always cold water) the Dual Valve Selenoid replacement FIXED the problem. Took 5 minutes to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDarryl from Prescott Valley AZ

Water not shutting off when filling tub and over flowing

First figured out tool to use to remove outer covering on control area. Then unplugged units from electric wiring and replugged with new parts.
Parts arrived in a very short time was very pleasantly surprised with the short turn around on ordering and recieving parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Fairview Heights IL

Water would not shut off when filling

I removed four hex screws from the top of the washer. I found the water level pressure switch and removed the dial. I turned it to remove it from the holding bracket. I removed both wires one at a time and placed them in the new switch one at a time so I wouldn't get them mixed up. I put the new switch in place and put the top back on using the hex screws. The dial was replaced. When I tested the dial I found that the dial did not match up to the water settings. They didn't even come close. Although the numbers were close on the switches, they were different. I had to remove the new switch and put the old one back on until I can locate the correct switch for my washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerJim from Marietta GA

Water coming out of bottom of washing machine

was a toss up between the water inlet valve OR the hose pressure switch....why spend more time...I invested in both the water inlet valve and the hose pressure switch and replaced them both....I have the machine torn apart....I spend $45 more dollars...now it's ALL done....and works like a charm...if I were to isolate the problem...I would say, now, the hose pressure switch...but, I am happy and machine probably has 5 plus, more years left...and life is good.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6