Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS271509
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.
I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008. I also power washed the basket and tub before reassembly. The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring. I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer. I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum. The entire job took 5 hours.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chisel and bust Old Alum. Nut off. Clean up and replace parts. OK. Had to remove water pump and clear debree that went in pump when spinner Hub broke off . the spinner also bursted a crack in the outer poly tube when it cam apart.. Sanded the dmage area and Patched with a good coat of JB Weld. machine is working Like new. The parts all worked Great. the break down Chart was a great Help to get the right parts needed. Thanks
the hardest part was getting the hub nut off. You have no room for a big wrench, I ended up chiseling it off.once I got it a part I saw the transmission was leaking oil, I checked every thing else, every thing seemed fine. I read on this web site that a common failure was the hub, mine was not in the best of shape so I replaced it while I was in there.replaced tub bearing,washer hub, hub nut , retaining clip for clutch,ring split, transmission and tub bearing 1/2 and $250.00 later the machine works like new.The diagrams that give you the part numbers were very helpful in the reassembly.
First I removed the agitator. The shoulder screw on top of the air bell was almost disintegrated, but after soaking with penetrating oil and a large channel lock pliers I removed the shoulder screw. Next, the air bell required a bearing puller to remove it from the agitator shaft (with force application to the agitator shaft from above). After two days of soaking with penetrating oil, heating with a hot air gun, and countless attempts with a pipe wrench and sledge hammer the 1 11/16 nut was not moving. I drilled down along the flats of the shaft and dug out as much corrosion as I could and filled the cavities with penetrating oil. Next, I drilled down at an angle (so as not to gouge the centering taper of the spinner hub) into the nut in order to relieve some stress - no success. I ended up using a chissel ( blade and flat round ) to break pieces of the nut away which was quite brittle. After removing about 1/8 of the nut's top and tapered portion, it began to turn out with a pipe wrench. Next, the spinner would not lift out off the shaft, so I had to remove the entire tub and transmission assembly (but with the spinner basket attached) as instructed by the paper stored within the control panel. I removed the tub support bracket and motor assembly and the pulley off the transmission (pieces of the brake pad fell out). Using a 2X6 piece of lumber, I fabricated 2 semi circular pieces to fit within the 20 inch diameter of the spinner basket and secured their position with another piece of wood. I attached eye hooks to the wood and with rope,hung the entire assembly over an I beam with the transmission in the 5 gallon bucket and the tub suspended only about an inch above the bucket. I hammered on the agitator shaft until the tub and transmission fell the inch as it separated from the spinner basket. After this, it was just cleaning the areas receiving new parts. I did use a sealant around the new tub seal edges and bottom when assembling. Other than having to tap 1/4- 20 threads in the new transmission brake flange (new part had no threads in the holes) the reassembly went fine. I did have to retighten the new 1 11/16 nut after the first use because the new brake pad really stopped the basket from spinning, but the momentom loosened the nut after 3 loads of wash.
Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.
Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.She led a good life.My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..
removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.
First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.PS: The washer runs great.
Simple R/R of oven element was easy. Washing machine was a complete teardown to the shaft to replace seal. Outer shell, tubs, motor and pump were removed. Was great to have exploded view of parts when it was time to reinstall. Parts were correct and fit perfect. Picture was not correct for the element but part was a match. Outstanding.
grab and yank off agitator ,used a socket to take off hub that covers hub nut and washer,took hub nut off and replaced tub bearing its a washer made of rubber and put new hub nut on pretty easy
Worse machine ever made. Installed all parts per videos .they helped a lot. Inner tub went on crooked and first wash ruined inner/outer tubs top piece. Took to dump.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.