| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Socket set
Customermichele from Deerfield Beach FL
Machine would not drain
I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerTammy from Belle WV
Water level would'nt empty to allow spin cycle
with a blade screw driver, I released the clips holding the front cover (from the top cover) tip the panel foward and lift off of pins on bottom. I put some towels in the bottom to absorb any water left after removing all I could with a cup. Then I released both clamps with pliers, pushing them back on hoses. Using a 10 mm nut driver, I removed the pump. I then mounted the new pump, pushed hoses on and slid clamps in position with pliers(while squeezing pliers) Voila, it works like it's new. Thank you Parts Select
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerDennis from Douglaston NY
Machine would not pump out completely leaving very wet, soapy clothes.
Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
Customermike from Manlius IL
The machine was pouring out water on the floor
i took out the two screws that mount the pump to the base of the washer, then i took a pair of channel locks to disconnect the clamps on the drain lines. thats it. i put the new one in and it works great!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:More than 2 hours
ToolsNutdriver, Pliers
CustomerHarold from Mocksville NC
Water was leaking underneath
remove screws from bottom of washer to remove the bottom of the washer so you can access the pump and motor assy. and remove two hose clamps.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers, Socket set
CustomerPaul from Medina NY
Pump was plugged
First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Socket set
CustomerJeffery W. from Bismarck ND
Pump leaking
First I uplugged the machine and removed the front cover of the machine by prying outward at the top corners with a screwdriver. Then I removed the two bolts from the mounting bracket and unplugged the electrical wires. Then using a pliers I squeazed the hosed clamps and slid them back on the hoses and pulled the hoses off the pump.
To install the new pump, simply reverse the order and check for leaks. The whole process took about 20 minutes.
|
0 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsPliers, Socket set
CustomerTerry W. from Mauldin SC
The pump motor stop working and the tub cover was cracked catching an picking clothes
I sold the washer to a friend of mine and gave him the parts as soon as I receved them. He passed on to me that everything was easy very simple 30 - 60 min he was done with both repairs. Everything worked great with no assembly issues. Also I recieved the parts ontime and faster then I expected. Thanks again. Terry F.
|