| |
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWalter from Boone NC
Dryer start knob was broken
Ordered new knob from you people and simply replaced borken knob.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Rahway NJ
Broken start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
Customerwesley from mcleansville NC
Drum was making noise and clothes wer getting hung between drum and outer panel
removed top panel of dryer, then removed the outer panel where the door is. glued new drum glides on and now it works great
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerElsa from Lorton VA
Timer had worn out & knobs needed replacing
I got the parts & a friend did the repair. He removed the "cover" from the top of the dryer to install the new timer. He "plugged" it back in, put the cover back with the screw driver & replaced the knobs & the dryer was good to go. It was much easier than I thought it would be. Getting the parts from you guys was awesome - the delivery was so speedy. If I ever need parts for older appliances that I cannot find at a hardware store, I will most definitely order from you guys.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDana from Provincetown MA
Had been broken off due to "plier" uasage.....duh!
Opened panel, bent retainer tab, took off wires. Took out switch, put in new switch, replaced wires and knob and plugged it in. Off she goes. PS, how the hell did you get that part to me in less than 24 hours??? Thanks guys.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLaurie from Fairfield ME
Inconsistant heat... had heat for one cycle and none the next or heat would stop half way through dry cycle
Removed the screws from the back of the control panel. Unplugged the old timer assembly and the timer knob. Plugged in the new timer assembly and put the timer knob on. Put the back panel back on and screwed it back on. Very simple. The dryer now works like new. It has instant heat right away and everytime it used. The selector knob was also installed by just slidding it on. I absolutely love this website...it's save me so much money in having to pay someone else to fix it. :)
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWagdy from Watertown MA
The two dial buttons were broken on a white appliance. The dials sent were bone white.
Pull out old, insert new.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMark from Miami FL
Knob broke
Pulled the old knod off and put the new knob on.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCatherine from Dunmore PA
Dryer wouldnt start
just replaced the old knob
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRosa from miami FL
Broken knob,and damage rotary start switch
replace both,in less than 5 minutes.save 80dollars in labor
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsScrew drivers, Wrench set
CustomerPeter from AMENIA NY
The on/off switch stem broke off
That happened because the on/off selector nob broke, so I instructed my wife to use a small pair pliers to turn the stem as a work around until I could get to it (6 mos). It eventually broke off. I called a repair service that charges $90 to look at it, but cannot estimate the whole job. The dilemma is that the dryer is over five years old, so a repair costing more than a few hundred dollars is not as reasonable as buying a new dryer. What to do? I ordered the parts and diagrams on the internet. They arrived two days later. The dryer is jammed into a narrow space, so to see the two screws in the back, I needed a small mirror on telescoping wand. To get at the broken switch, I needed unscrew two "star" screws and remove the control panel facing. Not Phillips head, not a common slot head. This star screw is hard to find. I finally located it in the fastener section. I bought a bit that fit my stubby ratchet screw driver. I had to use the stubby screw driver because it was such a cramped space. I finally got at the switch, loosened one screw (hex head) and replaced the two wires on clips - no solder needed. Got a kiss and a squeeze from the missus and a load of clean clothes.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerThomas from Bloomington MN
Broken dryer nob, broken lint screen.
Both parts arrived quickly and were exactly what I ordered. The lint screen replacement part was of higher quality and it works better than the one that came with the dryer. Very satisfied.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Strawberry Plains TN
Selector knob was broken.
Removed broken knob. Pushed new knob on shaft. Worked great.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJessica from Spanaway WA
Start knob on dryer broken
There really is not much to explain, the new knob was so simple to replace that my six year old could have done it. No tools were required and it took less than a minute to replace the new knob.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Wrench set
CustomerPeter from Mountainside NJ
Stem of rotary start switch broke off
Fairly simple. removed start wwitch by rotating it out of its position. There is realy only one way to remove it and it is intuitive. The new part is simply placed n the only position that the part will fit in the panel. Once the part is locked in placed, the new part is installed. Simply take you time and think it thru.
|