Quick Question!

Have you ever purchased from PartSelect.com before?

270835-1-S-GE-WH1X2117          -Timer Knob Clip
270835-1-S-GE-WH1X2117          -Timer Knob Clip http://www.partselect.com/Schematics/GE/00122776i01.gif

Timer Knob Clip

PartSelect Number PS270835

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will Not Start.

Compare At

$7.91

You Save

$1.32

Your Price

$6.59
Order within the next 10 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 19 reviews What's this?
1-15 of 19
 

141 of 172 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mr Dennis from Twinsburg, OH

Knob would not engage, had to manually turn outer ring to start washer.

Used a screw driver and needle nose pliers to remove clip from behind the timer knob. Took 2 minutes to remove clip, i admit it was a little tricky but once you get a grip on the clip very easily removed. Replaced with new knob, old knob gear was completley stripped . put the new clip on and presto, Like brand new.A normal service call would of ran me 45.00 just to tell me what was wrong with the machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46 of 49 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Kristina from Pasadena, CA

Timer on the washing machine wasn't working properly. Just spinning around not catching to set wash cycle

I found Partselect and searched for what I needed. Wasn't quite sure I had the right timer, so I called and gave them the model number and they did a search and found the right one. I ordered the part online and a few days later the parts were delivered to me. The timer fit right in and looked just like the origninal. Within 30 mins. washer was back in service.
Another washer we have on the property wasn't agitating correctly. After taking off the agitator ( by pulling straight up from the bottom ) I found that the coggs on the agitator hub were all worn out. I removed the center screw from the shaft and pulled the old hub off. Installed the new one ordered from Partselect and washwer was back up and running in no time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

33 of 43 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Gordon from BLUE DIAMOND, NV

Timer knob broke off where the dial compression ring fits.

All I had to do was pull out the broken timer dial assembly and push in the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

37 of 67 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: RICHARD from NEWARK, DE

Knob and timer di not work

remove back screws to control panel. unplug timer. pull bad timer out. snap new timer in plug in connector. reattach screws to control panel. put knob on timer

Help other customers find the most helpful instructions.

Were these instructions helpful?   

21 of 26 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Clifford from Sun Valley, NV

Teeth on timer knob broke off

Removed timer knob clip and installed new dial and timer knob

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 26 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: William from Hillsboro, OR

Gear teeth stripped out on both timer knob & timer.

Super EZ repair. The replacement parts were spot on perfect. I removed 3 screws, slid the panel off, removed a wiring harness, the reversed the procedure. I used a set of needle nose pliers to slip the locking ring on the knob, and Bob's your uncle, all done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: David L. from London, OH

The control knob plastic gear was stripped

took the needle nose pliers and removed the timer knob clip from the back of the control knob. Removed the control knob and the dial with compression ring. Installed the new dial compression ring and pushed the control knob on. Note: the new control knob comes with the clip allready on the back of the control knob. Took me about 3 minutes to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Kirk from Golden, CO

It appears the machine came with the wrong washer control knob.

I damaged the timer gears trying to figure out the washer control knob. I ordered all necessary parts. It now appears the knob that came on the machine had different gear hobs than the timer. I replaced the timer. The dial then easily slipped on. Then the control knob with the clip attached pushed on to the timer. I had an extra timer knob clip. It was just 93cents so I may need it later. It works better now than it did new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: STEPHANIE from Bluefield, VA

Dial spins too freely

The grooves on the bottom of the control knob were worn away. I just pushed the timer knob clip off of the underside of the knob, removed it from the washer and put the new knob on and put the clip back on. It was a piece of cake!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Joy from Pipe Creek, TX

The setting knob was broken and wouldn't engage

There is nothing to tell really. Took the setting knob off, put the new knob on. That was it, took all of five minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Cheryl from Erie, PA

The knob broke off. We glued it on but it still didnt work right.We still had to manually turn the dial. When I saw this site it showed a diagram and I figured out what was wrong.

Just took the dail off and put the knob on and slid the clip on. It was harder to take the glue off that we put on the knob!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Susan from Keyport, NJ

Spinning control knob

I watched the video, used a needle nosed pliers to pull the clip off the knob and just pushed the new knob and clip on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: JAMES from Boca Raton, FL

Timer knob defective

After viewing the brief video supplied by you,it was a simple five minute fix.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: CANDACE from AUSTIN, TX

Teeth on the dial with ring broke/stripped

Used a bent paper clip to hook/remove the old plastic Timer Knob Clip, pulled off Control Knob and Dial. The dial was ok but was afraid it may have been stripped also.I then replaced them and used needle nose pliers to replace Timer Knob Clip. I always order extra clips because they are cheap and have learned a long time ago nothing ALWAYS goes perfectly and it was cheap plastic and sure as you know what I would have broken it and had to order another. Now I have a spare!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Marie from Deltaville, VA

The control knob teeth broke-could not move it easily

we took off the old control knob-pulls off-then replaced the plastic clip and popped it back on-now the teeth can move the knob to start the washer

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 19