| |
14 of 16 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerScott from Denver CO
Dial broke off knob. Knob stripped.
Too easy! Push on dial, push on knob, insert clip. Done. Back in the day a repairman would have probably sold me a new timer with that knob and dial!
|
12 of 15 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerMarlin from Riverton WY
The local repair man ssaid we needed a timer switch for $90.00 plus labor
I took the control knob off and saw the teeth broken and got on line and ordered the part. It was an easy fix.
|
10 of 15 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerJanet from Post Falls ID
Dial for wash cycle wouldn't turn
opened the top part of washer where the dials are. Took out the old washer timer, inserted the new and replaced the knob and clip on the outside. Works like new.
|
7 of 12 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerKelly from Lewiston ID
The edge of the knob wore out
I pulled the old knob off and put the new one on.
|
4 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerJames from Ephrata PA
Teeth were stripped on dial
Just followed your instructions,which were very good and simple.Took old one off then put the Knob Dial on and it clicked right on..Very,Very easy
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerWilliam from Cornelia GA
Timer would not advance.
Removed the four torx screws on top of backsplash, unplugged timer, removed the one holding screw, slid timer back and removed.
|
4 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerDennis from Middletown RI
Wash cycle selection knob had plastic teeth on the underside that stripped out with years of use.
I used a pair of needle nose pliers and a screw drive to remove the clip holding the knob on its shaft. The new knob came with its clip already in place, so it "popped" right on. I ordered the compression ring in error and it it was not needed
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerStewart from Richmond KY
Knob wouldn't advance timer
Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerDavid from Sarasota FL
The teeth on the control knob were worn down, couldnt engage to start
after removal of the plastic clip with needle nose pliers and a screwdriver simply remove the knob and replace with new one and reverse the process for installation very easy and this site had the part for half the price of the GE site thank you
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBryce from Melbourne FL
Timer job would not turn dial
Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKaren from Canastota NY
The knob on my washer would not turn so I could select load size
I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.
|
2 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerEvelyn from Granite Bay CA
Knob didn't turn easily, pressure needed
Using screwdriver and pliers removed old knob; replacement snapped on easily.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customermichele from Deerfield Beach FL
Washer needed new knob and clip
simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid from Jonesboro TN
Control set knob no longer turned the setting dial
I reviewed the service guide on Partselect and was able to take the old knob off the washer and say that the teeth on the knob had worn off, I called in and ordered the part on Saturday and the part was delivered in Wednesday, within 2 minuets from getting home from work the washer was fixed. My wife was ready to go out and buy a new washer when it only cost a little over $13.00 to get it fixed.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerPablo from Houston TX
Old washer knob
Removed clip from knob and pulled out old knob.Then got new knob and installed with the new clip ,very easy job.
|