268331-1-S-GE-WE9M10            -Air Duct Felt Seal
268331-1-S-GE-WE9M10            -Air Duct Felt Seal 268331-2-S-GE-WE9M10            -Air Duct Felt Seal http://www.partselect.com/Schematics/GE/00005070i03.gif

Air Duct Felt Seal

PartSelect Number PS268331

If your dryer is making a squeaking noise this seal may need to be replaced.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Compare At

    $16.99
  • You Save

    $2.83
  • Your Price

    $14.16
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 10 reviews What's this?
1-5 of 10
 

15 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: John from Baytown, TX

Dryer sqeaking loudly after it warms up

I Removed the top cover by removing the two small screws just inside the dryer door at the top. The I removed the dryer front and door assembly by removing the two small screws inside the dryer front on each side. That's it. All the parts can then be accessed and replaced easily. The entire job took 10 minutes including a good cleanout.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 15 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Summit Health and Fitness from Flagstaff, AZ

Horrible screeching sound when dryer was running.

It took more time to figure out how to get the dryer apart than it did to fix it. Unfortunately I ordered the wrong parts the first time but Part Select was very helpful and efficient in helping me get the correct parts. I located the two screws that hold the top onto the machine inside the door frame at the top. Once the top was off, there were two screws that held the front door assembly to the dryer. The old parts (very worn and next to totally gone = none of the slides were remaining) were easy to snap out and the new parts easy to snap in to place. The Spa is happy that the dryer is quiet again and can be run when we have clients waiting. Thanks to you Part Select.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 14 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: ROBERT from CLIMAX, NC

Very bad squeak

I removed the top and layed it back with wires attached. Took out 2 screws and removed the front. I pulled out the drum and throughly cleaned away all lint and dust from motor, etc. Removed worn parts and reinstalled new parts in same fashion. Reassemble cabinet and check operation. . . . . Great. No new dryer needed!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Wrench set
Customer: Terry from Huntingdon, PA

Dryer made screeching noise when running

removed top by removing two screw inside door,
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Rebecca from Manitou Springs, CO

Loud squeaky noises when running

I had never tried to fix a dryer before, but I checked your site and found detailed troubleshooting instructions. I found several parts diagrams that made me think it would not be too difficult. I found the GE Repair manual for my dryer and ordered it. I was able to determine that the sqeaking was in the front, and probably the slides were worn, as opposed to the drum roller. Whew! My daughter and I removed the front and checked them. They were totally worn away and the felt was crimped. We cleaned it up and ordered the replacement parts from you. When they arrived we made the repairs. One of the drum slide holders was too worn to hold the new slide so we applied a bit of super glue to hold it in place. My dryer is running quietly again. I am so glad for your online information. This was an fairly easy fix!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 10