267091-1-S-GE-WE1X980           -D-Shaped Knob Insert Clip
267091-1-S-GE-WE1X980           -D-Shaped Knob Insert Clip 267091-2-S-GE-WE1X980           -D-Shaped Knob Insert Clip

D-Shaped Knob Insert Clip

PartSelect Number PS267091

Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not start.
  • Will not shut off.
  • Compare At

    $4.34
  • You Save

    $.72
  • Your Price

    $3.62
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 17 reviews What's this?
1-15 of 17
 

491 of 494 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJeffery from Waterford MI

Timer knob cracked twice. Found out the timer switch was bad.

Removed the 3 knobs. They just pull off. Removed 6 screws on the back side of the control panel. The front (plastic panel then just separates from the back). Then look at how the switch is mounted on the plastic panel. There should be 2 small pieces of plastic that holds it in. Carefully twist the switch in the appropriate direction so it comes free. Before you remove any wires from the old switch remember what colors go where ! I used needle nose pliers to remove the connections from the switch. Make the new connections, mount the switch, put the screws back in the panel. BEFORE YOU DO ANYTHING. UNPLUG THE ELECTRICAL CORD !!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

149 of 231 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWhitney from Vancouver WA

Start knob and plastic underneath broken

It was so incredibly simple! The site made it foolproof to find the right parts - and the actual replacement job itself was easier than we ever could have imagined. Background: I love to do laundry - I mean A LOT! So - I use the washer and dryer every night to wash the familie's clothing and blankets and towels. After heavy use - the outer knob stripped out. We threw it away and were using pliers to turn the small plastic knob underneath. After a few months - that plastic wore down and we could not turn it on at all!

Help other customers find the most helpful instructions.

Were these instructions helpful?

123 of 193 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set

CustomerEdwin from Seattle WA

Dryer making grinding noises

We live in a Condominium, space is tight especially in the Utility room where the washer/dryer are located. Turned dryer breaker off at the electical panel.
Removed the top cover and front assembly w/door and front drum support, right where the unit was located. Had to gain rear access to loosen drum drive belt so undid the dryer vent hose to floor connection through a front acess hole. Moved the unit out to the breakfast nook as well as disconnecting the power cable from the wall socket. Removed the rear access panel covers and unhooked the drive belt. At the front removed the top screws off the lower cross member to allow spreading of the side covers to allow the removal of the drum. Removed drum and found the bearing bushing gone, reduced to powder.
Using the supplied instuction sheet, replaced the rear bearing assembly, replaced the drum after vacumming the whole interior and started the reassembly of the unit using the new belt and moved the unit back into place. Reconnected the power cable and dryer vent then lastly replaced the lint filter and selector knob. Closed the breaker and turned on the machine, no noise!!!
Incidently I am 78 years old. Thanks PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

76 of 142 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDouglas from Santa Barbara CA

All the control knobs broke

I took apart the top of the dryer and removed the switch and replaced it with the new one. I also removed the knobs and replaced them. Easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

30 of 41 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench set

CustomerJosephine from Chevak AK

It would over flow with water

First I removed the 4 screws that held the element in place. I pulled it out, and than I decided to check on the hose that was attached to the water level pressure switch, so I opened the front of the washer and sure enough, all I had to do was clean the hose attached to the water sensor, and as it turned out, I really did not need to change the water sensor, but at least I have a water level pressure switch, water sensor just in case I really do need to change it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerKimberly from Valencia CA

I needed to replace the timer knob on my dryer

I took the old one off and the new one went right onto the dryer. It was very simple to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerThomas from Webster NY

Timer bound up, causing the knob to break.

Disassembled back splash to inspect timer. Ordered parts (at a 50% discount from brick and mortar stores). Parts delivered in two days. Installed new timer and had everything back together in 10 minutes. No-brainer!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWilliam from Islip Terrace NY

Start switch and knob busted

Just followed the installation video. The only issue with the video was that a phillips screwdriver was specified and I actually needed a torx screwdriver.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRosa from miami FL

Broken knob,and damage rotary start switch

replace both,in less than 5 minutes.save 80dollars in labor

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMichael from Scottsdale AZ

Timer failed

Replaced failde timer with parts. parts arrived quickly

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Knob
  • D-Shaped Knob Insert Clip

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerCharles F from Kirkville NY

Could not adjust timer/switch

I had immediately assumed the problem was the timer/switch, P/N WE4M365 and foolishly ordered that part. Should you ever encounter non-adjustment of the timer/switch, try another knob from the console. That was the only problem here as it turns out. Also, the knob DOES come with the "D" shaped insert clip.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 12 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerMikhail from Framingham MA

8 screws and done

After taking off:
5 screws off the back
2 in the front - Husky screws in the front
panel clips - the top panel was opened.

1 more screw for starter switch

DONE - under 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRichard P. from Bensalem PA

The timer switch on our dryer

The person on the phone was so helpful in locating the exact timer needed. We received the prt 3 days later and it was so easy to install. I would highly recommend this company. A local shop wanted to charge 3x more then what we paid.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerAdeline from Kendall WI

Timer had 2 spots it wouldnt clico past easy

replaced timer, knob. 30 minuted done. It was great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMichael from Strawberry Plains TN

Selector knob was broken.

Removed broken knob. Pushed new knob on shaft. Worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 17