Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS267091
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Removed the 3 knobs. They just pull off. Removed 6 screws on the back side of the control panel. The front (plastic panel then just separates from the back). Then look at how the switch is mounted on the plastic panel. There should be 2 small pieces of plastic that holds it in. Carefully twist the switch in the appropriate direction so it comes free. Before you remove any wires from the old switch remember what colors go where ! I used needle nose pliers to remove the connections from the switch. Make the new connections, mount the switch, put the screws back in the panel. BEFORE YOU DO ANYTHING. UNPLUG THE ELECTRICAL CORD !!!
Help other customers find the most helpful instructions.
Were these instructions helpful?
It was so incredibly simple! The site made it foolproof to find the right parts - and the actual replacement job itself was easier than we ever could have imagined. Background: I love to do laundry - I mean A LOT! So - I use the washer and dryer every night to wash the familie's clothing and blankets and towels. After heavy use - the outer knob stripped out. We threw it away and were using pliers to turn the small plastic knob underneath. After a few months - that plastic wore down and we could not turn it on at all!
We live in a Condominium, space is tight especially in the Utility room where the washer/dryer are located. Turned dryer breaker off at the electical panel. Removed the top cover and front assembly w/door and front drum support, right where the unit was located. Had to gain rear access to loosen drum drive belt so undid the dryer vent hose to floor connection through a front acess hole. Moved the unit out to the breakfast nook as well as disconnecting the power cable from the wall socket. Removed the rear access panel covers and unhooked the drive belt. At the front removed the top screws off the lower cross member to allow spreading of the side covers to allow the removal of the drum. Removed drum and found the bearing bushing gone, reduced to powder.Using the supplied instuction sheet, replaced the rear bearing assembly, replaced the drum after vacumming the whole interior and started the reassembly of the unit using the new belt and moved the unit back into place. Reconnected the power cable and dryer vent then lastly replaced the lint filter and selector knob. Closed the breaker and turned on the machine, no noise!!!Incidently I am 78 years old. Thanks PartSelect.
I took apart the top of the dryer and removed the switch and replaced it with the new one. I also removed the knobs and replaced them. Easy
First I removed the 4 screws that held the element in place. I pulled it out, and than I decided to check on the hose that was attached to the water level pressure switch, so I opened the front of the washer and sure enough, all I had to do was clean the hose attached to the water sensor, and as it turned out, I really did not need to change the water sensor, but at least I have a water level pressure switch, water sensor just in case I really do need to change it.
I took the old one off and the new one went right onto the dryer. It was very simple to do.
Disassembled back splash to inspect timer. Ordered parts (at a 50% discount from brick and mortar stores). Parts delivered in two days. Installed new timer and had everything back together in 10 minutes. No-brainer!
I had immediately assumed the problem was the timer/switch, P/N WE4M365 and foolishly ordered that part. Should you ever encounter non-adjustment of the timer/switch, try another knob from the console. That was the only problem here as it turns out. Also, the knob DOES come with the "D" shaped insert clip.
The person on the phone was so helpful in locating the exact timer needed. We received the prt 3 days later and it was so easy to install. I would highly recommend this company. A local shop wanted to charge 3x more then what we paid.
Just followed the installation video. The only issue with the video was that a phillips screwdriver was specified and I actually needed a torx screwdriver.
Replaced failde timer with parts. parts arrived quickly
After taking off:5 screws off the back2 in the front - Husky screws in the frontpanel clips - the top panel was opened.1 more screw for starter switchDONE - under 15 minutes.
replace both,in less than 5 minutes.save 80dollars in labor
replaced timer, knob. 30 minuted done. It was great!
Snapped the parts right on. Fast service and easy repair.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.