266250-1-S-GE-WE18X26           -Lint Filter with Frame
266250-1-S-GE-WE18X26           -Lint Filter with Frame 266250-2-S-GE-WE18X26           -Lint Filter with Frame 266250-3-S-GE-WE18X26           -Lint Filter with Frame http://www.partselect.com/Schematics/GE/GE_Thumb/00009195i04.gif

Lint Filter with Frame

PartSelect Number PS266250

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Takes too long to dry.
  • Compare At

    $14.51
  • You Save

    $2.42
  • Your Price

    $12.09
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 23 reviews What's this?
1-5 of 23
 

167 of 196 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerMichael from Warwick, RI

The rear drum bearing was worn the dryer became very noisy

i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make sure the wires are not in the way and remove the drum.i also used a vacuume to clean the inside of the dryer. the front drum slides are very easy to replace only 2 screws each.remove old parts install new parts then just put the dryer back together in the reverse order i took it apart. after re-assembly i turned the dryer on it was so quiet running my wife and dogs were very happy. ps. i just want to thank the people at partselect for having all my parts in stock and for the speed in which i received them. other than having to repair my dryer it was a very pleasant experiance.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 10 people found this instruction helpful

Parts Used

  • Lint Filter with Frame

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerRaymond from Vassar, KS

Had a lint filter that screen was all worn out

We ordered a new lint filter with white frame from Part Select. Had to take the dryer outside and blow all lint out that had accumulated in the dryer. We then vacumed everything out and brought back in house and put in new lint filter we ordered and used the dryer today and it works beautiful. Saved us from having to buy a new dryer. Thanks Part Select for having the filter we needed. Raymond Kampsen, Vassar, Ks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 12 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerMark D. from Kittery, ME

Damaged belt

Disconnect and clean all duct work.

Note: Lint is combustable, save yourself the disaster of a dryer fire.

Position dryer face down on floor.
Access rear of unit, vacume clean.
Upright unit.
Access front of unit by removing sheet metal screws above door to float the lid.
Using screwdriver gently seperate drum at top from housing. Hold open with wedges.
Thread new belt through hole a foot or so.
Tape belt to drum near drum center.
Rotate drum until belt is fully around.

Note: Taping new belt to drum will assist you in reassembling. Belt will not fall off drum when unit is face down on floor.

Remove wedges and resecure sheet metal screws to top of unit.
Place the unit face down again.
Ensure belt clears all front mounts.

Note: gentaly pull drum from mount and slide belt between.

Remove old belt and idler pully.

Note: replace the idler pully with every new belt it will save you time later.

Install new idler pulley and rethread in new belt.
Rotate drum to access and remove tape attaching new belt to drum.
Upright unit and test.
Re-attach access panels, reposition unit and
re-attach duct work.
Done

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Lint Filter with Frame

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerDomenic from Livingston, NJ

Lint filter had holes in it. Req. Replacement,

Simple - took out the defective filter and replaced with the purchased part. The hardest part was figuring out the right lint filter. The extensive info on PART SELECT was very helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Lint Filter with Frame

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerChristine from Auburn Hills, MI

The lint filter on my 28-year-old dryer had holes in the screening.

I removed the old lint filter and put the new one in! Grateful to find this item for my "antique" dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 23