263918-1-S-GE-WD7X14            -Door Cable and Eyelet
263918-1-S-GE-WD7X14            -Door Cable and Eyelet 263918-2-S-GE-WD7X14            -Door Cable and Eyelet 263918-3-S-GE-WD7X14            -Door Cable and Eyelet http://www.partselect.com/Schematics/GE/GE_Thumb/00002537i02.gif

Door Cable and Eyelet

PartSelect Number PS263918

This part is sold individually. It is recommended that both sides are changed when replacing one.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door latch failure.
  • Door won’t close.
  • Compare At

    $10.20
  • You Save

    $1.70
  • Your Price

    $8.50
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

SPRING DR

Part Number 259712

Sold Individually

$27.55
In Stock

Heavy Duty Door Spring

Part Number 259673

Used for dishwashers that have decorative wood panels. Sold Individually.

$42.29
No Longer Available

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 46 reviews What's this?
 

2 of 3 people found this instruction helpful

Parts Used

  • Door Cable and Eyelet

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerGeoffrey from Centreville, VA

Cable broke to the spring attachment for tension on the door.

The cable attachment comes with the two hole loop assembly that the springs hook into. With the lower panel off and the door closed, the other end of the cable assembly hooks onto the fitting on the side of the door. No tools required except the phillips head screw driver to take off the lower panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Door Cable and Eyelet

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerThevinh from El Monte, CA

One cable was boken

1 - unscrew that holded the machine in place, these screws were on the top of machine.
2 - pull out machine about 5 inches.
3 - unscrew the cover at the bottom cover. there were 4 screws, 2 on the left and 2 on the right.
4 - connect 2 cables in series with 2 springs.
5 - hook one end of 1st cable to the left pin and the other end of 2nd cable to the right pin.
6 - slide both cables lay on both wheels.
7 - Tight all 4 screws back to their place and push machine in place.
8 - tight the last 2 screw which hold machine in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Cable and Eyelet

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerGlenn from San Bruno, CA

The springs keep the door from falling too fast. When the cables break, the door free falls.

There are 4 phillips screws on two covers at the bottom front of the dishwasher, when they are removed, the cables and springs are accessible.
The springs and cables are replaced by hand only. Then the covers are replaced with the 4 screws.
DONE.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Cable and Eyelet

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerTim from Acton, MA

Cable attached to the door spring broke

Took lower access panel off. Replaced broken cable and attached to double spring.

When it broke my wife wanted a new dishwasher? It cost $13.80 to fix and door works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Door Cable and Eyelet

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRichard from Santa Rosa, CA

The door spring assembly broke

This was surprisingly easy. I removed the 4 sheet metal screws that held on the lower colored panel on the front of the dishwasher. I hooked one of the cables to the little post on the bottom right edge of the door, and then hooked the other cable on the post at the bottom left. I then hooked the two door springs to one of the cables, stretched out the springs a half inch or so, and hooked them to the other cable, making sure the cables were seated on the wide rollers. I then opened the dishwasher door a few times to make sure all was well (it was) and replaced the 4 screws + lower panel. Voila!

Oh, and I cleaned around the edges of the lower panel while it was out. They are hard to get to when the panel is installed, and they were quite filthy, I'm embarrassed to say.

Help other customers find the most helpful instructions.

Were these instructions helpful?