Lower Spray Arm with Tower

PartSelect Number PS260604

This part may differ in appearance, but functions same as original.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Compare At

    $32.27
  • You Save

    $5.38
  • Your Price

    $26.89
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 8 reviews What's this?
1-5 of 8
 

36 of 45 people found this instruction helpful

Parts Used

  • Lower Spray Arm with Tower

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerWilliam from Middle Island, NY

Top of the water spray "tower" was broken off by opening lower dish drawer and not checking to see if tower was in the down position.

Apply large vice like pliers at base of the lower spray arm and not applying too much pressure to plier as this is an all plastic part and slowly turn counter-clockwise until entire spray arm is loose enough to lift out and install the new part in the reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

35 of 50 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerAaron from Liberty Township, OH

Washing poorly, leaving particles of food on top of the dishes, not draining completely, ceiling spray arm not spinning (bent up to the ceiling)

The lower spray arm unscrews. From inside the dishwahser, put a screwdriver through the tab slots and unscrew the tower from the floor. It's pretty tight for plastic.
The upper spray arm has screws on the top of the dishwasher. You must slide the dishwasher out from underneath the countertop to get to the screws. Normally that's just the two screws above the door that screw into the countertop. Pull the insulation back and unscrew the arm from the top of the dishwasher. Reverse to reinstall.
Piston and nut assembly for check valve: Inside the dishwasher at the back there are 2 screws that hold a screen down. Remove the screen. Take out the check valve and replace it. It was still functional in mine, it looked like food gunk had built up on it and impeded the check valve action.
The flapper chec is a rubber flap in the drain tube that connects to your sink drain. You have to pull the dishwasher out from under the sink to get to the end of the drain tube that connects to the dishwasher. Take the hose clamp loose and remove the drain tube from the dishwasher. Then unscrew the plastic fitting that you just took the drain tube off of. The flapper chec is there. It had turned brittle and didn't flap anymore. It is a similar setup to the rubber seal at the end of your garden hose.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Lower Spray Arm with Tower

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerSTEPHEN from MYERSTOWN, PA

Extention broken on lower wand sprayer

turn wand counter clockwise until it's out,replace it with the new one.DON'T OVERTIGHTEN!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Lower Spray Arm with Tower

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEvelyn Rae from Tallahassee, FL

Broken spray arm tower

I removed the broken lower spray arm tower using a scew driver and snapped in the replacement part not needing any tools.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Lower Spray Arm with Tower

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench (Adjustable)

CustomerKevin from Valrico, FL

Lower arm extention wand broke off.

Getting the upper part of the lower arm out was easy. It is just tabs that hold it in. Screwing the old one out was the hardest part it was fused in with dried detergant but once it was loose it was a real easy to put the new one back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8