May look different than the original, but will function the same.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not fill with water | Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric.
Part# WD15X10004 replaces these:
AP2039344, 824332, WD15X10002, WD15X10006
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
water inlet valve leaking
I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish wash
... Read moreer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.
Read less
Brad from wadsworth, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set, Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Larry
November 13, 2017
When closing the dishwasher door and pushing the start wash button, it sounds like the motor starts running although no water is entering the washer, could this be caused by the water inlet valve, if not what could be the problem.
For model number GE Washer, PDW7880G00SS
Hi Larry,
Thank you for your question. I would say that would be a good place to start. You can test your water inlet valve with a multi meter to check to see if it is working or not. You could also check your float switch as well. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Carey
January 25, 2018
My dishwasher fills with water, but it does not go into the spinners to wash the dishes. The detergent (pods and liquid) is left in the compartment with the door open. I have cleaned out the filter at the bottom but I cannot find a float to check that. Any advice on what it could be?
For model number PDW8000G01BB
Hello Carey,
Thanks for your question. You will want to test the water inlet valve and the pump for continuity with a multimeter, and replace them if they do not show continuity, as those are the most common causes for your issue.
I hope this helps.