Quick Question!

Have you ever purchased from PartSelect.com before?

259157-1-S-GE-WD12X332          -White Track Roller Kit
259157-1-S-GE-WD12X332          -White Track Roller Kit 259157-2-S-GE-WD12X332          -White Track Roller Kit 259157-3-S-GE-WD12X332          -White Track Roller Kit http://www.partselect.com/Schematics/GE/00125643i02.gif

White Track Roller Kit

Compare At

$6.16

You Save

$1.03

Your Price

$5.13
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS259157
Manufacturer Part Number WD12X332
Manufactured by GE

The track roller on your dishwasher allows the tracks that hold the upper dish rack to slide in and out effectively. If you notice that your upper dish rack is struggling to slide in and out, you may need to purchase a new track roller kit to replace the damaged one. This kit comes with the roller, one screw, and a washer for easy assembly. The roller is approximately 1-1/4 inches in diameter and the screw is approximately 1-1/2 inches in length. To complete this repair, you will need to remove the upper dish rack, as well as the rail.

This part works with the following brands: General Electric, Hotpoint, Kenmore.

This part works with the following products: Dishwasher.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 4 reviews What's this?
1-4 of 4
 

19 of 26 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Dave from Littleton, CO

Parts were old and worn out

The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: ROBERT from YOUNGSTOWN, OH

Upper tray very difficult to pull out and push in

Using a screwdriver removed upper tray slide end caps.
Removed upper tray.

Removed and replaced upper tray rollers.

Using screwdriver removed track rollers and Track.

Assembled track with rear stops.
Installed lower track rollers.
Holding track in place installed upper track rollers. Installed upper tray and and front track stops.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • White Track Roller Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Howard from Mount Prospect, IL

The upper try roller was broken

Unscrewed the old roller. But it was difficult to replace the roller as the rim of the roller would not fit into the slide mechanism and allow the screw to engage the hole. What I thought would be a 2 minute job turned out to be more like 20 minutes. I suspect there is a way to release the slide stop so that the top basket could be removed with its slide bar, but I did not see how to do that. I finally was able to "force" the screw into the hole

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Dave W from Granite Bay, CA

The upper rack would fall off when pulled out

I installed new rollers and rack clips. The old ones had cracked and would not keep the rack in the tracks. I went to buy a new dishwasher which would have cost around $500. I bought $60 worth of parts although I probably could have just bought the clips for $15 and now the dishwasher is good to go! A real money saver.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4

Model Cross Reference

This part works with the following models:

PartSelect Number: PS259157
Manufacturer Part Number: WD12X332
Brand Model Number Description
Kenmore3631401190Dishwasher
Kenmore3631401191Dishwasher
Kenmore3631401590Dishwasher
Kenmore3631401591Dishwasher
Kenmore3631401592Dishwasher
Kenmore3631401890Dishwasher
Kenmore3631401891Dishwasher
Kenmore3631401892Dishwasher
Kenmore3631402190Dishwasher
Kenmore3631402191Dishwasher
Kenmore3631402192Dishwasher
Kenmore3631402590Dishwasher
Kenmore3631402591Dishwasher
Kenmore3631402592Dishwasher
Kenmore3631402890Dishwasher
Kenmore3631402891Dishwasher
Kenmore3631402892Dishwasher
Kenmore36314031000Dishwasher
Kenmore36314031001Dishwasher
Kenmore36314032000Dishwasher
Kenmore36314032001Dishwasher
Kenmore36314038000Dishwasher
Kenmore36314038001Dishwasher
Kenmore36314039000Dishwasher
Kenmore36314039001Dishwasher
Kenmore3631404193Dishwasher
Kenmore3631404194Dishwasher
Kenmore3631404196Dishwasher
Kenmore3631404197Dishwasher
Kenmore3631404593Dishwasher