Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS259136
The lower dishrack wheel on your dishwasher allows the dishrack to roll in and out effectively. If your lower dishrack wheels are damaged, or the rack does not roll in and out, you may need to replace them. This wheel is located on the front lower rack and includes the axle. This part is sold individually. The wheel and the axle are made of white plastic. The lower front dishrack wheel is approximately 1.5 inches in diameter. To complete the repair, simply detach the damaged wheel and axle from the rack, and install the new one by snapping the axle in place.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
I took it out of the package and snapped it on the drawer and slide it back in the dishwasher. The part cost way to much but it was worth it to continue to use my dishwasher
Help other customers find the most helpful instructions.
Were these instructions helpful?
The new roller easily clipped together and then clipped into place on the lower dishwasher rack.
Installation of the two new lower rack rollers was extremely easy. Simply aligning each of the new rollers and pressing them into place completed the task in a few seconds.
first I had to put the pins in the rollers (could of put the pin in at the factory). then took the old rollers off and put the new assembled parts (roller and pin) on. they fit fine and no more falling off.(just a question: is partsselect in canada?My credit card charged me an international fee.)
Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.
just snap wheels in place. But customers should know that the sale only includes 1 wheel for about $20.00 with shipping and handling!!!!
Just simply attached where the other roller had been...no installation...was so glad to be able to find and have shipped so quickly.Thanks,G. Boling
Pushed the roller onto the axle, then snapped it to the rack.
Popped the wheel in-- just like that! everything fixed!a P. S. --- right after I replaced the missing wheel, my wife found the original wheel which had come off and slipped under the kitchen cabinet.That's OK. Now I have a good source of repair parts I didn't have last week!! (and a spare wheel in the process). Thanks Chas Field
The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.
I disassembled the rack and figured out how to remove the rack rollers before placing my order with PartSelect. I am a visual person and usually don't need to read directions. I was having some difficulty removing the end caps of the metal sliding racks which encase the rack rollers. I used my mother's staple remover (not the traditional kind) in order to pop off the end caps without breaking them. Once the parts came in the mail it was easy to pop off the end caps, apply the new rack rollers and reattach the end caps without breaking them. I enjoy doing business with PartSelect but I have to admit these parts are extremely expensive. I think it is ludicrious to spend a lot of money on "plastic." Products are not made to last in today's society. When I was a kid appliances would last a homeowner anywhere from 15-20 years or more - not today!Thank you PartSelect for your time and assistance - I just wish these parts were cheaper.
Snapped off the old wheel and discovered that the wire that held the wheel seemed bent, so I straightened it with a pliers and then snapped the new wheel on. It was so easy.
I removed the 4 screws that hold the mesh drain cover in place . I used pliers to loosen the check valve piston and nut assembly at the rear of the appliance . I screwed in the new piece by hand . While I had the dish racks out , I put a new set of wheels and rollers on them . I was 5 minutes away from buying a new dishwasher , but this website saved me HUNDREDS of dollars . My dishwasher is as good as new now .
Super-easy and quick repair -- quality part snapped right into place.
This is more of a nuisance problem than repair. We have had this excellant dishwasher for years and the last two or so years the wheels kept coming off, my wife would get on me to put them back, after a while she would just lay them on the counter and i would get the message. the reason they kept coming off was because over time the retaining plastic was sprung or broken off. I tried to repair them with glue,tape,etc. nothing worked for long. I am handicapped and couldn't get to the store. I ordered the part from you and got them that same day, my wife and I were amazed. Thank You!!!!!!!!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.