Quick Question!

Have you ever purchased from PartSelect.com before?

249424-1-S-GE-WB44X200          -Bake Element - 240V
249424-1-S-GE-WB44X200          -Bake Element - 240V 249424-2-S-GE-WB44X200          -Bake Element - 240V 249424-3-S-GE-WB44X200          -Bake Element - 240V http://www.partselect.com/Schematics/GE/00006230i02.gif

Bake Element - 240V

PartSelect Number PS249424

This bake element kit comes with two installation screws.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.
  • Little to no heat when broiling.
  • Touchpad does not respond.

Compare At

$43.34

You Save

$7.22

Your Price

$36.12
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 173 reviews What's this?
 

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Walter from Lake Kiowa, TX

Element burnt in two

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Richard from Arlington, TX

The oven was not reaching the desired temperature

If the bottom heating element is not glowing red when you turn the oven on replacing this part may be the answer. Look for a spot on the old element that could indicate it has shorted out and no longer carries a charge.
Very simple to remove the two screws holding the element in place, pull the element out about 3 inches, disconnect the two wires, replace with the new element and reattach the two screws. Simple and effective. The new element is fast and responsive. Do this before any other suggestions to replace more complicated parts in the thermostate etc.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Gregg from Centennial, CO

Burned out element

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Thomas from Haviland, OH

Broken element

Removed the two screws that held the element in place. Pulled the unit out a few inches to get at the bolted wires. The hard part is reaching in the oven using bifocal lenses and trying to block out the oven light. Getting past that obstacle, the rest went very well.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Keith from Wauwatosa, AL

Old element burned out

Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: jerome from Farmington Hills, MI

Heating element was on fire and needed to be replaced

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Dennis from Norcross, GA

Replace burned out element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Diana from Millbrae, CA

Heating element corroded.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: JEFFREY from Duanesburg, NY

Oven not heating properly. Oven lights out.

Removed bake element by taking out the screws of the element plate at the back of the oven. Pulled out the bake element and disconnected the two electrical wires attached to the element by screws. Screwed on the new element and reattached the back plate. The light bulbs (upper and lower oven) were replaced by pulling up on the wire holding the light bulb protective glass enclosure in place, removing the enclosure and then unscrewing the light bulb. Then screwing in the new bulb and re-attaching the glass enclosure.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Carol from Evergreen Park, IL

Simple, unscrew and then re-screw

Simple, unscrew and then re-screw

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: John from Mount Vernon, OH

Lower heat element burned out

having read instructions from previous PartSelect users it was a snap. Nutdriveer, and screw driver were the only tools needed. This was a wall oven and the most difficulty I had was getting to the nuts with the door open. I really didn't want to take off the door.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Bill from S. Glastonbury, CT

Bake element in oven would not heat.

Turn off circuit breaker. Release bake element from back of oven with a phillips head screwdriver. Remove bake element from heating wires with an adjustable wrench. 1/4 nutdriver was a little to big large for the old screw. Do not allow wires to fall back into the installation. Reverse the procedures for installing the new bake element. Most difficult part of the repair is having old eyes and not being able to focus on the work site which is about 12- 14 inches from your eyes. Young people with good eyes no problem. Oven heats like a new unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Derral from Edmond, OK

Heat bake went out

Flipped the breaker, checked that there wasnt power. Unscrewed the 2 screws holding the bake to the back wall of oven. Used nut driver to unhook bake from electical leads. Used new screws from new bake to attach to leads. Mounted bake with original screws to back wall oven.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Norman from Houston, TX

Oven bake element broken

Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Wrench set
Customer: Nancy from Burlingame, CA

Burned out oven element

we of course turned off the power. the box wrench loosened the nuts. the part fit easily in our 30 year old oven. It was easy to attach the leads to the heating element--a bit awkward, but we finished the job in 20 minutes. At first, the new element looked different from the old one, but it fit perfectly. The oven is as good as "new" needs cleaning!

Help other customers find the most helpful instructions.

Were these instructions helpful?