| |
0 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
Customerkay from monroe NC
The bake heat element was broken.
The part I ordered was a perfect match for the broken unit.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I removed the broken element put the new one in reattached the wires and then put the two screws back it. Oven works perfect.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJames from Raleigh NC
Bottom heating element broke.
Unplugged oven, removed 2 screws from the rear of unit and disconnected power connectors for heating element. Replaced broken element wint new assembly, reconnected neutral/hot connectors and reattached rear cover. Very easy repair.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver
CustomerKevin from Peoria AZ
Bottom heating element burned itself out
First I pulled stove out away from wall and unplugged the power cord then I removed the oven door to make repair much easier. I removed the two screws holding the heating element in place. I then went behind stove and unscrewed four screws to remove panel covering the electrical connections. Disconnected wires to heating element. Removed old element and reversed each step to connect new element.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerPaul from Waunakee WI
The bottom heating element was burned out and needed to be replaced.
1. Pull out all the cooking racks for best access. 2. Remove the two hex head screws at the bottom back of the oven cavity that hold the element. 3. Gently pull the element out towards you. The electrical prongs will slide out from the insulation. Pull them just far enough to clear the electrical connections. The connections slide off the ends - use a pliers or needle nose as they fit tightly. 4. Snap the electrical contacts on to the new element, then feed them back into the back of the stove cavity. 5. Replace the hex head screws.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
CustomerBrian from Falls Church VA
Element different
Bake element made slightly different than original.The non removabal metal plate to cover opening for wires at the oven rear was to small. Had to fabricate cover with sheetmetal with holes in it for the elements conductors to go thru.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerPaul from Beverly Hills FL
Replace heating element
It was so easy I can't believe in the past I would have called Sears because I have such a" no handy man" gene in my body person. I saved over $150.00 by doing it myself. Took out eight screws, pulled the old heating element out, replaced the old with the new, put eight screws back, put the range back in place, plugged it in, turned it on and walla, done deal. Less then 10 minutes, I swear
|
0 of 2 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerJohanna from Charlton MA
While making supper, we realized the bottom heating element wasn't working.
We decided to go "on line" to see if there was any way to fix the stove ourselves and found the Part Select website. After entering the model number for the stove, we were able to find the heating element. We ordered it and received it two days later! We saved money and time. Thank you!
|