Quick Question!

Have you ever purchased from PartSelect.com before?

249286-1-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V
249286-1-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V 249286-2-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V 249286-3-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V http://www.partselect.com/Schematics/GE/00116954i03.gif

Bake Element - Push On Terminals - 240V

Compare At

$65.54

You Save

$10.92

Your Price

$54.62
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS249286
Manufacturer Part Number WB44T10011
Manufactured by GE

The bake element in your oven provides the cooking heat. This part can be found at the bottom of your oven, and attaches to the power source on the back wall. It has two terminals that fit into the power source receptacle. This part is made of metal, and is approximately 20 inches in length and 18 inches in width. This product is sold individually. Many of our customers have rated this repair as easy. To complete this repair, simply lift the old element up and out of your oven, and replace it with the new one. Be sure to disconnect power from the oven before you begin this repair.

This part works with the following brands: General Electric, Kenmore.

This part works with the following products: Range.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Oven is too hot.
  • Will Not Start.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 108 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Jeff from Quilcene, WA

Lower element burned out in the oven.

Turn power off. Then I removed the two small screws holding the element to the stove wall. Tip it up as you pull it out of the oven wall being a little carefull as the wires to the element are very short! I only had about an extra 1/2" of wire. Pull wires off of the old element and part them on the new one being carefull NOT to loose them back in the stove wall. Push the new element back into the oven wall and replace the mounting screws. 5-10 minutes tops. J.V.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: edward from estero, FL

My lower heating element broke

My 8 year old son did the repair while I explaned what to do,that was the best part of this stove problem. My burner caught fire when it broke and really scared my children. I looked up the part on Part-Select and ordered it. To my complete surprise it arrived the next day(I did not pay for overnight) My son wanted to learn how to take out the old one and put in the new one so I let him. Thanks for a GREAT learning time with my son and for your super service!! Ed

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Wrench set
Customer: ALAN from CHARLOTTE, NC

Bake element burned out

Removed back cover of stove. . . Just a few screws. . . Disconnected 2 terminals to bake element. Then removed 2 screws inside the oven. . . Holding the element. Replaced with new element. . . Reattached the two mounting screws inside the oven. . . Attached terminals in back. . . Replaced back cover that covered the terminals and other connections. That was it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: fred from hermon, NY

Bake ekement burnt out so oven would not heat

I removed the 2 screws that held the element in place. I then pulled the element out and removed the 2 wires. I was able to connect one wire to the new element, but the second wire drew back though the opening. I then had to pull out the stove and remove the center cover on the back of the stove by removeing the screws, there were five or six. do not forget the one in the center of the bottom. I then connected the second wire and replaced the back cover and slid the stove back in place. I then replaced the 2 screws that held in the element in and was done. Worked good as new and no repair bill.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Michael from Houston, TX

Broken oven bake element

Removed the 2 screws that hold the element in place in the oven. Pulled on the element to expose the wires. At this point the element which was initially just cracked ,broke completely appart ,at the crack into 2 pieces. (Confirmed obvious element failure lol..) Ordered a new element and decided to just plug in the range so as to be able to use the stove till it arrived. Blue sparks and now no power at all to the stove. frustrated at my ignorance I go out side and check the breaker. It seemed ok,so now i worry about a blown fuse. I took the back panels off with appropriate socket and cant find a fuse..JUST GREAT!! i notced a burn mark where the wire connects to the element and figured out that it shorted because it was touching the inside of the oven ..I had not pushed it back flush. I found out how to simply slip the connector off of the element with the back open and now pushed the element back in place. I taped the wires with electrical tape so they would not short on anything,checked the breaker again and turned it off for a second..then back on. This time when i plugged the range back in I had power..whew what a relief!! When the new element arrived it took 10 minutes to take the 2 screws back out ,swap in the new element and slide on the wires to the connectors. I reinstalled the backing plate ,and put the 2 screw back in to hold the element. Problem solved!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Davis from Longwood, FL

Baking element was broken

1. Turn breaker to off position.
2. Using socket wrench, remove the old element.Takes a little prying to remove the connection from the eletrical wires.Be careful.
3. Insert new part and tighten with socket wrench.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: steve from melbourne, FL

Oven element cracked

pulled out old element by unscrewing the 2 bolts in the back and vcarefully pulled out the two wire s . wires are very tight so if you let go of them which i did you will need a pair of needle nose plires to pull them out. other than that the installation is easy

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: CHARLES from OAK ISLAND, NC

Burned-out bake element

Turned off power to stove. Removed burned-out element by removing two sheet metal screws and disconnecting two push-on electrical terminals.

Installed new element by pushing on electrical terminals. Pushed the new element back in place and secured with two sheet-metal screws.

Turned power back on and tested element. All OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: MIKE from FORT WAYNE, IN

Bottom oven element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and held them out with two pair surgical scissors. Besure you hang onto wires because they are a bear to get back thru hole.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Wrench set
Customer: Victoria from Downingtown, PA

The heating element was broken

I googled and did the step by step removal and installation of the element from a web site.. EHow

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Jason from Norwich, CT

Replace bake element

Unplugged the stove.

Needed 1/4 inch socket to remove screws holding element and the back panel.

Removed the electrical connections on the element and then removed the old element and replaced with the new element.

Replaced screws holding the element in the oven.

Replace the electrical connections on the element in the back of the stove.

Replaced the back panel.

Plugged the stove in and tested out.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Tim from Conway, AR

Oven heating element had burned out.

Removed 2 hex head machine screws. Picked up on the element and slid wires through. One wire became unattached. Removed back panel, pushed wire through the oven wall, and replaced the back panel. Wires connected with push on connectors. Pushed attachment assembly back through the oven wall and replaced 2 machine screws. Viola! Working oven.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Samuel from Oviedo, FL

Oven element burned out

2 screws removed holding element in. Wires are very short and after removing from the element one wire went back into the insulation. Had to remove the back from the range to get access to wires.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Timothy from Show Low, AZ

Change out baking element that did not last as long as it probably should have.

Removed old baking element by removing two sheet metal screws inside the oven and pulling out the old element. When pulling out the old element, one of the wires was too short and popped back into the back of the oven. I then had to pull out the oven, take the shielding off the back of the appliance, gain some slack in the wire and push it back into the interior of the oven. I connected the new element and was finished with the repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Juli from Lake City, MN

Bake element burnt out

First my husband removed the two screws that hold the element in place. Then pulled the element out and diconnected the two wires. The wires popped back in, so he took the shield off the back, I pushed the element in so he could see the prongs and hooked the wired back on. He then replaced the 2 screws and i was back to baking.
Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS249286
Manufacturer Part Number: WB44T10011
Brand Model Number Description
General Electric15891 1Range
Kenmore91195852991Range
Kenmore91195857991Range
Kenmore91195859991Range
General ElectricECBP70SK1SSRange - Electric
General ElectricECBP70SK2SSRange - Electric
General ElectricECBP70SK3SSRange - Electric
General ElectricECBP70SK4SSRange - Electric
General ElectricECBP70WK1WWRange - Electric
General ElectricECBP70WK2WWRange - Electric
General ElectricECBP70WK3WWRange - Electric
General ElectricECBP70WK4WWRange - Electric
General ElectricECBP82BJ1BBRange - Electric
General ElectricECBP82BJ2BBRange - Electric
General ElectricECBP82BJ3BBRange - Electric
General ElectricECBP82SJ1SSRange - Electric
General ElectricECBP82SJ2SSRange - Electric
General ElectricECBP82SJ3SSRange - Electric
General ElectricECBP82SK1SSRange - Electric
General ElectricECBP82SK2SSRange - Electric
General ElectricECBP82WJ1WWRange - Electric
General ElectricECBP82WJ2WWRange - Electric
General ElectricECBP82WJ3WWRange - Electric
General ElectricECBP82WK1WWRange - Electric
General ElectricECBP82WK2WWRange - Electric
General ElectricECBP85WJ1WWRange - Electric
General ElectricECBP85WJ2WWRange - Electric
General ElectricECBP85WJ3WWRange - Electric
General ElectricEER2000C00BBRange - Electric
General ElectricEER2000C00CCRange - Electric