249286-1-M-GE-WB44T10011-Bake-Element-Push-On-Terminals-240V.jpg
249286-1-S-GE-WB44T10011-Bake-Element-Push-On-Terminals-240V.jpg 249286-2-S-GE-WB44T10011-Bake-Element-Push-On-Terminals-240V.jpg 249286-3-S-GE-WB44T10011-Bake-Element-Push-On-Terminals-240V.jpg

Bake Element - Push On Terminals - 240V

PartSelect Number PS249286

This bake element is found on the bottom of the oven.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little or no heat when baking.
  • Oven not heating evenly.
  • Cooktop element not heating.
  • Oven is too hot.
  • Will not start.
  • Compare At

    $56.76
  • You Save

    $9.46
  • Your Price

    $47.30
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 97 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerRita from Spartanburg SC

Bake element burned

Repair was fairly easy. Had the problem that I had read about with one of the connection wires falling behind oven. Time consuming to take of back of stove but otherwise all went very well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

Customerduke from charleston SC

Change oven element

Cut off stove at breaker box then remove shelves.use a nut driver, quarter- inch to remove two screw that hold element in then carefully pull the element out about two inches they have a push on clips that holds the wires to the element use a piece of wire to keep the push on clips from going back into the stove.Pull the clips off with needle nose plyers and reconnect. Most important thing don't let the wires pull back into stove. Duke

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerPAUL from TOOELE UT

Bake element went out

FIRST TURN OFF THE BREAKER TO STOVE THEN REMOVE PANEL ON BACK OF STOVE ABOUT 12" WIDE AND ABOUT 30" TALL 6 OR 7 SCREWS. THEN PULL WIRES OFF OF ELEMENT, THEN GO INTO THE OVEN AND REMOVE 2 SCREWS, PULL OUT ELEMENT, THEN SAME THING IN REVERSE VERY EASY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerTony from Oakland TN

Current bake element burned out.

First unplug the unit from the outlet. Then remove the rear cover, covering the electrical wires. Disconnect the hot /ground wires from the element leads. Then open the oven door and use the nut driver to remove the inner screws to release the bake element. Insert new element and replace all screws and electrical leads. You're all done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRaymond from Madisson FL

Oven not heating up to temperture

replaced heating element. Took less then 15 minutes to repair. Ordered the heating element on Monday morning received new element by noon the folowing day. It was actually painless to repair, great company to do business with. Thank You so much

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerVernon from Springville IN

The oven lower heating element was burned out.

I removed the racks and oven door. I used a socket to remove the screws that secured the element. I pulled the element out to gain access to the wire connectors and used pliers to remove the wires from their connectors to the burned out element. I installed the new element by using the pliers to secure the wire connectors to the element and then installed the element with the socket thus securing the element with the screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerKatherine from North Eastham MA

Burnt out oven coil

turned off power to stove.
removed old coil, as instructed by internet info.
replace new coil.

il

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerCorey from Orange Park FL

Bake element cracked

The repair was easy to fix. I unplugged the stove to be safe, unscrewed the broken element and disconnect. And reconnected the new element and screwed it into place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerMarion from Charlotte NC

Burned out bake element

It was so simple.after turning off power 1. removed oven door 2.used nut driver to remove the screw nuts. 3.used clothes pins to hold wires and prevent them from falling back into insulation. 3.connected new element to wires and inserted into insulation area. 4.reconnected the nut screws. 5.replaced door. 6.turned power back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMary from Jersey Village TX

Bake element burned out

Removed 2 screws, removed element, replaced element, replaced 2 screws - Worked great

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyDifficult

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerVicki from Longmont CO

Bake element burned out

Turned off power to the stove, had my tools ready. I had read about replacing this part so I thought I was prepared, well the most difficult part of it all was the wires hooked to the bake element, they do not come out very far from the back of the stove, maybe 1 inch not much to work with & you do have to secure them with some type of clamp so you do not loose them into the back of the stove, (I had read about some people having to pull the stove out, take the back cover off & stick the wires back through, I did not want my husband to have to do that, Ha Ha) besides for the wires being to short everything went well. Put it all back together & turned power on & tested the stove "IT WORKS" again. Thanks to everyone that shared their stories It helped me!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPatricia from Norwood NC

Replaced burned out bottom heating element

My husband did the repair, I held the light.
Pull out stove, unplug it, remove the screws with the nut driver, free old element from clips, put in new element and hook up clips, replace screws in the new plate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench set

CustomerJoyce M from Newport TN

Element caught fire and burned up

My son read all the blurbs on line and came prepared to keep the little clips from slipping into the insulation. No problems, it was quick and simple. I recommend reading instructions on line from others, they gave good tips

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRonald from Wooster OH

Oven would not heat above 200 deg.F

Turned off power. Removed 2 nuts at rear of oven and pulled the heating element out to expose end connections. Slipped wire connections off old element and onto the new element, placed back into place and tightened the 2 screws. About 10 minutes. Works great. Thanks to PartSelect for a great troubleshooting guide.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerLouella from Waldron MI

Bottom bake ewlement burned out

Wasn't sure exactly what part number to order, called Parts Select, very nice lady on the phone helped me find the correct part#, I ordered it and approx. 24 hours later it arrived. Shut the power off to stove, removed the two screws on the back wall, gently pulled the connecting wires through (still attached ) to the element. Disconnected the wires and put a spring type clothespin on them so as not to lose the wires back in the insulation. Connected new element, put power back on. I was amazed how easy a job it was, thanks to reading some of the instructions on this forum. Not to mention saving a bunch of money. I will definitely order from PartsSelect whenever the need arises.

Help other customers find the most helpful instructions.

Were these instructions helpful?