Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS249286
This bake element is found on the bottom of the oven.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.
Help other customers find the most helpful instructions.
Were these instructions helpful?
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.
Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.
I turned the breaker off to the stove and moved it away from the wall. I then removed the center cover off the back of the stove and exposed the wires connected to the bake element. I removed the wires from the bake element and then opened the oven and removed the two bolts holding the element onto the back wall of the oven. I discarded the old element and replaced it with the new first bolting the new in , then connected the two wires and replaced the rear cover. Turned on the power and made a cake.
So easy. Took extra time so the wife would think it was harder. Just read the other reviews for instructions. Didn't have an issue with the wires pulling back into the oven though I did have my "clips" ready.
Really easy even i could do it , it was a little fiddly and the wires disappeared into the back of the oven , i easily removed the rear panel and pushed the wires back thru and connected them , turned the breaker back on and sparks !!removed the rear panel again in 2 mins and saw that the wires were touching the oven frame and had shorted out , it wasnt a problem moved them slightly, reconnected them to the element tightened them up , put breaker on and Done , took about 45 mins but i could of been done in 30 with a little more care in the beginning of the job EASY !
This was the second repair on this stove. It is less than 2 years old. I won't buy an other GE stove as long as I live. The first repair was replacing the burner recepticles. They just melted away. This time the bake element blew a hole in it causing flames to shoot from it. It was easy to get the right parts, but I only worry what will go next. How long will the replacement parts last? Oh boy!
First I unplugged the stove. Then I removed the two screws inside the oven to remove the heating element. For safety purposes I removed the back panel from the stove also to get a complete view of what I was getting into. That was just 5 more screws and the panel came off and exposed what the heating element was plugged into. Very easy to unplug and reconnect, install the back panel then install the two screws for the heating element and it works just fine.
First, my husband removed the two screws that hold in the element. Unfortunately, my GE Spectra oven had extremely short wires. That was the only thing that made it somewhat difficult. So, he pulled the element out as far as he safely could, replaced it with the new one. No problem! As I said, the only thing that made it difficult was the short wires supplied by GE. The part came from PartSelect.com with no problems. I would definitely use this website again to order parts.
After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire leads out of the insulated rear of the oven.Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.