249286-1-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V
249286-1-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V 249286-2-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V 249286-3-S-GE-WB44T10011        -Bake Element - Push On Terminals - 240V http://www.partselect.com/Schematics/GE/00116954i03.gif

Bake Element - Push On Terminals - 240V

PartSelect Number PS249286

This bake element is found on the bottom of the oven.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Oven is too hot.
  • Will Not Start.
  • Compare At

    $65.75
  • You Save

    $10.96
  • Your Price

    $54.79
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 97 reviews What's this?
1-5 of 97
 

183 of 197 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Dennis from Bondville, VT

Oven element burned itself up

Turned off circuit breaker to range.
Removed the 2 oven racks. Removed two screws in back of oven compartment. Pulled element forward and the terminal connections get exposed.
The right terminal clip disconnected by itself and the wire went back into the stove and could not be retrieved.
Removed range draw under the oven and pulled entire range out from wall about 4 feet.. Removed metal backing with a socket wrench and exposed the oven element wires and terminals.
Reinstalled new element and metal backing.
Since range was out from wall, cleaned and vacuumed before pushing stove back in place.
Since range draw was out re-leveled by setting adjustable feet.
Reinstalled drawer and racks.
Turned on circuit breaker.
Tested element by setting bake cycle on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

105 of 108 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Theresa from Sherman, TX

The baking assembly in the oven burst into flames one day, then broke apart.

After the element cooled down, I pulled the racks out of the oven, turned off the oven at the breaker box, then, using a nut driver, loosened the screws that held the baking assembly in the back of the oven, and pulled the connecting wires off. I bent the wires to make sure they would stay out, because if they get back in the insulation, they are hard to find. I would recommend getting a pair of locking pliers and putting them on the ends of the wires just to keep them from getting back into the insulation. Then I attached the left connection wire and then the right one, pushed them back into the insulation, tightened the baking assembly to the back wall of the oven, turned it back on at the breaker box, then tested the oven to see if it heated up. It did. Total repair time 15 -20 minutes. Would have been less if I didn't have to chase one of the wires back in the insulation. Shamless plug for the company ...By paying extra for 2-day shipping to receive the part, I saved just over $20 from buying it at Sears, which would have had to order the part anyway.

Help other customers find the most helpful instructions.

Were these instructions helpful?

45 of 48 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: russell from hampstead, MD

Element burned out

removed the oven racks. used a 6.5 mm socket to take out two bolts. pulled out old element and wires through insulation into oven. i used caution during this part i didn't want the wires to disconnect and fall into the oven. once the wires and element was pulled out approximately 3 inches. i used two magnet clips that hold papers onto the refrigerator and clipped both wires so they wouldn't go back into the stove. disconnected the element from the wires and connected the new element to the wires. pushed wires into the back of the oven and tightened the two 6.5 mm bolt. done in 10 minutes. turned oven on to 400 degrees and let same pre heat. a little smoke will come from the new element which is normal. works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

37 of 38 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Robert from Sussex, NJ

Baking element broken

After I got the right part(I ordered the wrong one at first, my fault) it was simple to remove the old element, 2 screws and push on termilnals, and replace with perfectly fitting new part. Word of caution, turn off the breaker to stove. I found that the element line is hot even if the control is off!

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Matt from Westr Grove, PA

Baking element and dual stovetop burner were fried

Baking element:First, turn off your breaker so you don't get injured. Using a small nut driver, remove the two screws that hold the element into the back of the oven. Once the screws are out, the element slides out, toward the oven opening. Be careful not to pull too hard, or the wires could disconnect from the back and be difficult to retrieve. Once the wires are exposed, disconnect them from the terminals. Attach them back to the new element, and put it back in. EASY For the stovetop, this is a glass top, so the burners are underneath. There are two small screws on the underside of the stove top, where the oven door closes. Remove those screws and then lift the front of the entire stove top. It will hinge at the back. There are two screws and little metal brackets that hold the burner in place. Remove those screws and brackets, disconnect the wires, and be sure to remember which wire goes where. Reattach the wires and screw the brackets back into the burner. Refasten the stovetop and you are good to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 97