Quick Question!

Have you ever purchased from PartSelect.com before?

249238-1-S-GE-WB44K10005        -Bake Element - Push On Terminals - 240V
249238-1-S-GE-WB44K10005        -Bake Element - Push On Terminals - 240V http://www.partselect.com/Schematics/GE/00115410i02.gif

Bake Element - Push On Terminals - 240V

Compare At

$82.34

You Save

$13.72

Your Price

$68.62
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS249238
Manufacturer Part Number WB44K10005
Manufactured by GE

The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.

This part works with the following brands: General Electric, Hotpoint, Kenmore.

This part works with the following products: Range.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 35 reviews What's this?
 

4 of 6 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kelly from Charlotte, NC

Baking element not getting hot

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Sabina C. from Hershey, PA

Burned out bake element

I ordered part at 10am on Monday and part arrived at Noon on Tuesday 24 hours WHAT MORE can I say... It was all easy and now I have to cook again, so much for the stove is broken excuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Nancy from RUSH, NY

Oven coil burned out

Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: ryan from NOVATO, CA

Oven heating element broke

Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Rita from LOCUST, NC

Oven element broke

Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: jannis from PHILLIPSBURG, NJ

The element broke in 2....

Pull out wires & replace element by putting wires back in then tighten...done!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Rickey from Childress, TX

Lower oven element burned into

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Joseph from DIAMOND SPGS, CA

The lower,bake, element had burned in half almost causing a fire.

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: Mary from ALOHA, OR

The bottome heater element of my oven burned out.

I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to the range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: MICHAEL from MORROW, GA

Oven would not heat up

I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Mark from SARASOTA, FL

Would not heat

Did the repair just like the video shows.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: SUZANNE from DAVID CITY, NE

Oven wouldnt bake food very well it took to long to bake

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Charlean from Lyon, MS

Lower element burned out

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: ronda from kingston, OK

No heat in oven

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Barry from Malvern, PA

Bake element burned out

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS249238
Manufacturer Part Number: WB44K10005
Brand Model Number Description
General Electric154510Range
General Electric155910Range
General Electric157710Range
Kenmore36261101000Range
Kenmore36261101001Range
Kenmore36261108000Range
Kenmore36261108001Range
Kenmore36261741000Range
Kenmore36261741001Range
Kenmore36261742000Range
Kenmore36261742001Range
Kenmore36261748000Range
Kenmore36261748001Range
Kenmore36262492000Range
Kenmore36262492001Range
Kenmore36262780100Range
Kenmore36262780101Range
Kenmore36262780102Range
Kenmore36262780103Range
Kenmore36262781000Range
Kenmore36262781001Range
Kenmore36262781002Range
Kenmore36262781003Range
Kenmore36262781004Range
Kenmore36262788000Range
Kenmore36262788001Range
Kenmore36262788002Range
Kenmore36262788003Range
Kenmore36291112000Range
Kenmore36291112001Range