244800-1-S-GE-WB32X5075         -Drip Bowl - 6"
244800-1-S-GE-WB32X5075         -Drip Bowl - 6" 244800-2-S-GE-WB32X5075         -Drip Bowl - 6" http://www.partselect.com/Schematics/GE/00007611i01.gif

Drip Bowl - 6"

PartSelect Number PS244800

This 6 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $6.43
  • You Save

    $1.07
  • Your Price

    $5.36
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drip Bowl - 8"

Part Number 244801

This 8 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.

$5.51
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.9 / 5.0, 18 reviews What's this?
1-5 of 18
 

8 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Michelle from West Bend, WI

The drip pans were unusable due to excessive use, and I decided to replace the surface elements as well.

There was nothing to it...I unplugged the Sufrace Elements from thier bases, removed the Drip Bowls, replaced the Drip Bowls and then plugged the Surface Elements back in to thier bases. The entire process could not have taken more than two minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Angelo from Duson, LA

Terminal block and 8" element shorted

Unpluged range. Removed back cover to access the infinite switches . removed old burner and drip pan. removed terminal block and retaining screw on cooktop. removed terminal block wiring from infinite switch taking care to mind were the wires came from. Install new terminal block and reattached to cooktop . installed new 8" burner and drip pan reinstalled back panel and plug in electrical to unit . tested burner . replaced stove after verifying burner worked

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Carol from Brookfield, WI

I needed new drip pans

I lifted out the burners and took out the old drip pans ans then replaced the burners. However the 8 inch pans were bigger than the old ones and they do not fit properly. They are sitting on top of the stove and not inserted like they should be. I will have to look elsewhere to find ones that fit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: David from Placerville, CA

Not heating properly

Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Joe from Mount ephraim, NJ

No power to element/no heat

removed burnt out terminal block, installed new- I soldered wires instead of using wire nuts, took a little extra time, but I feel it's a better connection. I later found that my rotary control must have burnt out too, I swapped it with one from another burner. I'll be ordering a couple rotary controls next from this company. All parts were nice quality. Received quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 18