244783-1-M-GE-WB32X5059-Porcelain-Drip-Pan-6.jpg
244783-1-S-GE-WB32X5059-Porcelain-Drip-Pan-6.jpg 244783-2-S-GE-WB32X5059-Porcelain-Drip-Pan-6.jpg

Porcelain Drip Pan - 6"

PartSelect Number PS244783

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $9.98
  • You Save

    $1.66
  • Your Price

    $8.32
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Porcelain Drip Bowl - 8"

Part Number 244785

$9.75
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.8 / 5.0, 3 reviews What's this?
1-3 of 3
 

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHOWARD from WATERBURY CT

Burners heated irratically

1. Pulled out drawer
2. Vacuumed dust, etc. under stove
3. Reached under stove to rear and pulled plug
4. Pulled the stove out away from wall so I could get to back
5. Removed 5 screws that retained the back of the control panel
6. One by one, I removed each wire from an old control and pushed it onto the same pin on the new control - did same for all 4 burner controls
7. Removed the knobs
8. Removed 2 screws from the front panel for each old control and removed the old controls
9. Pushed each of the new controls into place on the panel and reused screws to secure them in place
10. Cut the long control stems using 2 pliers per instructions to match length of old controls.
11. Used knob adapters provided to mate the old knobs to the new control stems
12. Plugged the stove in and tested the burners
13. Unplugged and replace the panel back with original screws
14. Moved stove back into place
15. The right front burner was the one most used, so I replaced the connector for that burner.
16. That connector came with instructions that I followed - cut the wires to the old connector, splice the wires to the new connector wires using supplied wire nuts and shrink tubing.
17. Plugged the stove back in
18. Replaced drawer - job complete - stove like new

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerAlfred from East Northport NY

Element would not heat to max temp.

The interesting part of this story was troubleshooting the problem. Was it the element or the control? Turns out the element was making poor contact, generating excess heat ,which corroded the element contact generating even more heat, and so on and so on until the termional block eventually broke. The repair itself was simple once I separated the element from the terminal block. After that I removed the terminal block, one screw, removed the connecting wires, two screws, reversed the procedure to install the the new terminal boplck and element. Before the whole process began I made sure to turn the breaker to OFF.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJoseph from Guilford NY

Small elements were losing heating power and large elements did not work.

I unplugged each element from the terminal it was plugged into and then plugged the new element in. I also replace the drip pans and trim rings while I was at it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3