244475-1-S-GE-WB31X5013         -Trim Ring - 6"
244475-1-S-GE-WB31X5013         -Trim Ring - 6" 244475-2-S-GE-WB31X5013         -Trim Ring - 6" 244475-3-S-GE-WB31X5013         -Trim Ring - 6" http://www.partselect.com/Schematics/GE/GE_Thumb/00009937i03.gif

Trim Ring - 6"

PartSelect Number PS244475

This 6 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $3.40
  • You Save

    $.57
  • Your Price

    $2.83
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Trim Ring - 8"

Part Number 244479

This 8 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.

$3.64
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 31 reviews What's this?
 

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

Tools

CustomerTommy from Hydro, OK

Burner rings and drip pans stained

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRandall from Lititz, PA

Bake element was bad and drip bowls needed replaced

First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured it by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDavid from Madera, CA

Burner would not heat

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerAlfred from East Northport, NY

Element would not heat to max temp.

The interesting part of this story was troubleshooting the problem. Was it the element or the control? Turns out the element was making poor contact, generating excess heat ,which corroded the element contact generating even more heat, and so on and so on until the termional block eventually broke. The repair itself was simple once I separated the element from the terminal block. After that I removed the terminal block, one screw, removed the connecting wires, two screws, reversed the procedure to install the the new terminal boplck and element. Before the whole process began I made sure to turn the breaker to OFF.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerSteven from Lancaster, PA

"burner" died.

By cleaning the connectors on the stove burners I have kept the stove alive for 20 years, but one stopped working because the terminal block connectors had burnt out. It was a simple one-machine screw holding in the original, so I swapped them, then took off the panel behind the controls to plug in the new connectors from the prewired terminal block. The rings were just a little touch to convince my wife that we do not yet need a new stove.

Help other customers find the most helpful instructions.

Were these instructions helpful?