Quick Question!

Have you ever purchased from PartSelect.com before?

244310-1-S-GE-WB31K5079         -Large Burner Drip Bowl
244310-1-S-GE-WB31K5079         -Large Burner Drip Bowl 244310-2-S-GE-WB31K5079         -Large Burner Drip Bowl http://www.partselect.com/Schematics/GE/00116988i01.gif

Large Burner Drip Bowl

Compare At

$23.74

You Save

$3.96

Your Price

$19.78
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS244310
Manufacturer Part Number WB31K5079
Manufactured by GE

This part works with the following brands: Kenmore, General Electric.

This part works with the following products: Cooktop, Range.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Medium Burner Drip Bowl

Part Number 244311

This burner drip bowl is sold individually. It is white on the top side, and black underneath.

Order within the next 3 hrs and your part ships today!
$21.63
In Stock

Small Burner Drip Bowl

Part Number 244312

This burner drip bowl is sold individually. It is white on the top side, and black underneath.

Order within the next 3 hrs and your part ships today!
$17.00
In Stock

Burner Bowl Seal

Part Number 244599

This gasket goes under the burner bowl to help protect the glass from high heat. Sold individually.

$23.09
No Longer Available

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 10 reviews What's this?
1-10 of 10
 

16 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Yuli from Old Bridge, NJ

Burner bowl paint began chipping

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...it was easy!

But note: almond bowl I had cost twice as much as white one I've bought. Almost NO difference in color!
The screws cost$1.65 ea at a PartsSelect, so I went to Home Depot and bought 10 pieces for about $2 and they are stainless, will not rust as original ones did.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Paula from Seal Beach, CA

The porcelain had chipped on the burner bowls

Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Bill from Corona, CA

Worn / chipped bowl

Removed two screws, pulled out the igniter wire, removed a spring type wire holding the igniter to the bowl. Replace with new bowl, reconnected wire and placed new washer around bowl, placed back on stove top and screwed in place. Less than ten minutes to replace and only used a phillips screw driver.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Mary Alice from Mill Creek, WA

Drawer was bent, bowl was scratched, burner was chipped

Followed instructions with replacements. Ordering was not that clear. Was asked the size of the bowls (large, medium, or small, and I measured them and all four bowls measured 9". I ordered 2 large bowls. However, that was not the measurment needed , it was the distance of the drilled hole and the igniter so I was able to use only one bowl. I have saved the other.
Mary Alice Krueger
Washington

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Jeff from Roseland, NJ

Igniter switch stopped working on one burner

The most difficult part of the repair was getting the front panel off. I needed to remove the top of the stove, which was easy but awkward - remove the two screws from each of the four burner bowls. Lift the bowls one by one, disconnect the wire and slide off the small clip under each igniter. Move the bowls and igniters out of the way. You will find a piece of sealant underneath the stove top covering the length of the front panel. You need to gently pry it off by lifting the stove top just enough to break the seal. Once the top is separated just gently move it to the back of the stove. You can now remove the 3 large screws underneath the front panel. There are also 2 screws under the plastic anchors that hold the front panel in place. Be careful, there are hidden screws in the back of each anchor, so don't break them. You just need to loosen them just enough to wiggle the front panel out. With the panel moved, the igniter switches are mounted over each knob. There is a spring washer clip holding them down. Gently pry off the clip of the damaged switch and disconnect the two wires. Make sure you put the wires back in the same order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Large Burner Drip Bowl
Level of Difficulty: Very Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers
Customer: Keith from Frisco, TX

Burner bowl mounting holes out of alignment

No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put to much pressure on the side of the hole.

Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.

I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.

I did not get new gaskets for the burner bowl but would reccommend that you get them.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: robert from SALIDA, CA

Cleaned up the cooktop with new parts.

Super easy, needed a screw diver and about 5 minutes per burner. (I replaced 4 each) Removed the 2 screws, disconnected and removed igniter. Put a new gasket on new burner bowl, reinstalled/connected igniter, installed the bowl with the 2 screws. Then I removed old knob and replaced with a new knob. New looking cooktop in about 20 minutes. The parts fit and look great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Large Burner Drip Bowl
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Sara from AURORA, IL

Scratches in drip pan from improper cleaning, spills during cooking.

The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: George from mission viejo, CA

The burner bowls were discolored

Real simple to do. Simply remove the two screws holding the bowl and disconnect the electric wire. Obviously first pull the power cord to prevent being shocked.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Large Burner Drip Bowl
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: John from San Bruno, CA

Remove and replaced cooktop stove tray

Easy, just remove two top screws, unplug the igniter wire and then do it in reverse. Your're done in less than 15min.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-10 of 10

Model Cross Reference

This part works with the following models:

PartSelect Number: PS244310
Manufacturer Part Number: WB31K5079
Brand Model Number Description
Kenmore36333355590Cooktop
Kenmore36333356590Cooktop
Kenmore36333359590Cooktop
Kenmore91132355590Cooktop
Kenmore91132355591Cooktop
Kenmore91132356590Cooktop
Kenmore91132356591Cooktop
Kenmore91132359590Cooktop
Kenmore91132359591Cooktop
Kenmore91132384101Cooktop
Kenmore91132385100Cooktop
Kenmore91132385890Cooktop
Kenmore91132386890Cooktop
Kenmore91132389100Cooktop
Kenmore91132389890Cooktop
Kenmore91133355590Cooktop
Kenmore91133355591Cooktop
Kenmore91133355592Cooktop
Kenmore91133356590Cooktop
Kenmore91133356591Cooktop
Kenmore91133359590Cooktop
Kenmore91133359591Cooktop
Kenmore91133384100Cooktop
Kenmore91133384101Cooktop
Kenmore91133385100Cooktop
Kenmore91133385890Cooktop
Kenmore91133386890Cooktop
Kenmore91133389100Cooktop
Kenmore91133389890Cooktop
Kenmore91136755590Range