244055-1-M-GE-WB30X359-Tilt-Lock-Hinge-Mounted-Surface-Element-6.jpg
244055-1-S-GE-WB30X359-Tilt-Lock-Hinge-Mounted-Surface-Element-6.jpg 244055-2-S-GE-WB30X359-Tilt-Lock-Hinge-Mounted-Surface-Element-6.jpg 244055-3-S-GE-WB30X359-Tilt-Lock-Hinge-Mounted-Surface-Element-6.jpg

Tilt Lock Hinge Mounted Surface Element - 6"

PartSelect Number PS244055

This tilt lock hinge mounted surface element kit includes a 6 inch, two wire, 1350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Cooktop element not heating.
  • Compare At

    $29.15
  • You Save

    $4.86
  • Your Price

    $24.29
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Tilt Lock Hinge Mounted Surface Unit - 8"

Part Number 244046

This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.

$34.01
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 20 reviews What's this?
1-15 of 20
 

18 of 22 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerCharles from McAllen TX

Two 6" and two 8" burner elements needed replacing on a 36 year old counter range.

First of all I want to thank PartSelect. I have been looking for these parts for over 15 years. I am so happy to have found PartSelect. 1. Turn off Range 2. Turn off Breaker to the Range at your home Breaker Box. 3. Turn on Range to see if you turned off the right Breaker if so then turn Range off. 4. Lift Burner Element up. 5. Take off Silver Trim Ring and Drip Bowl. 6. With screw driver unscrew the screw that is holding the Burner Element to the Range. It is located at the base of the hing where the Burner Element attaches to the Range. 7. Pull the Burner Element out just far enough to see the entire Element where the wires attach. 8. Snap off the two silver clips from each side of the White Glass Insulation Block with a screw driver. 9. With an adjustable wrench (crescent) loosen and remove the screws holding one of the wires to the Burner Element. 10. Find the same Terminal on the new Burner Element and reattach the wire to the new Burner Element Terminal. 11. Now do the same to the remaining Terminal. 12. Install the White Glass Insulation Block over the two Terminals and secure with the two silver clips. 13. Reattach Burner Element to Range with screw. 14. Replace Silver Trim Ring and Drip Bowl. 15. Turn on Breaker and test by turning on Range. You will smell a slight electrical burn smell for a moment while the new Elements heat for the first time. This will dissipate quickly. NOTE: I used the old White Glass Insulation Block I did not use the one that came with the new Burner Element. I found the old one to be the better choice. I saved the new one in case needed at a later date. The Job to replace both the 6" & 8" Burner Elements took less than 30 Minutes. I think it took longer to write this replacement instruction. LOL Very easy...Thanks again PartSelect. Charles McAllen, Texas

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerKENNETH from SAN ANTONIO TX

Bunner triangular support legs had broken

unscrew hinge support screw w/nutdriver, remove ceramic insulator held on with clips around wires and base of burner, remove screws holding wires to element w/nutdriver, replaced screws on new element w/nutdriver, replaced ceramic insulator held together w/ clips, reattach hinge, replace burner lower overflow bowl and trim ring, fire it up. used pliers to hold the wires and burner element together when tightening screw so as to not bend element.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerStephen from San Pedro CA

Electric range heating unit (burner) inop

Removed single screw securing the old tilt-up burner. Removed clips on sides of clamshell ceramic terminal block with flat blade screwdriver to expose two wire connections. Removed 2 screws connecting the wires to the bad heating element. Did not use the supplied new ceramic terminal block, just reused old one. Connected new burner to wires with 2 screws. Reassembled terminal block with clips. Fastened clip with single screw to attach new unit to side of opening in range top. Tested. Done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerThomas from Boulder Creek CA

Replacement of broken element

Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJenean from San Jose CA

One burner was not level and the otherone I burned out tea kettle on it and when I pulled the kettle off the burner it was also not level not to mention part of the kettle was burned onto the burner.

I didn't turn the power off which was risky and dangerous, however it was very easy just removing one screw a couple of wires and installing the new one. VERY EASY!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerRosemary from New Port Richey FL

Heating unit had seperated from my coils.

A friend had stopped by and insisted on replacing the heating element on my 32 year old range. It took him all of 45 minutes to replace it, and now it works like a charm.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJim from Marco Island FL

Stove top burner died of old age.

Removed the hinge mounting screw and disconnected the wiring. Hooked up the new element and replaced the mounting screw. A quick and easy $45 repair (part +shipping) that I am quite pleased with. Jim W., Marco Island, FL

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customergeorge from belmont CA

Burner damaged

replaced burner ( attached wth 2 screws )

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerShirley from McClellanville SC

Burners on stove & oven element had begun to over heat and one had broken apart

Ordered replacement burners & oven element thru your website and installed. Burners & oven are working fine now. I have had to order an oven element in the past; about 5 - 8 years ago. I've owned this stove now for over 20 years.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers

Customercharlie from lost creek KY

2 of the top burners did,nt work

Got parts super quick! Everything exactly the same for a range over 30 yrs, old!! Lift up element,(hinged)remove 1 mounting screw, disconnect 2 wires, remove & replace drip bowl,reconnect 2 wires,put on trim ring, replace mounting screw, lower element (hinged) back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJoann from Townsend GA

Burner burnt out

replace it .works great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench set

Customeralan from Tallahassee FL

Replaced rusted out burner

I have tilt up burners on my Range, and decided to replace one that have finally rusted out the part that holds it in place. Repair was easy- installed according to the enclosed instructions. Parts arrived in good condition and very timely. A+

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Tilt Lock Hinge Mounted Surface Element - 6"

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDelores from Carlsbad CA

Bracket under electric bruner was broken .

I followed the instruction that was enclosed with the parts and found it to be very easy to install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerLisa from Queensbury NY

Old counter top stove in disrepair!

We have the original 1970's counter top stove and the elements were breaking!!! My 13 year old son replaced the two elements (I think the process is not that hard to do and I don't know the steps... sorry!) and dad helped him make the drip bowls fit (since we haven't been able to find parts locally!)

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerRoger from Cypress TX

Element had burned out.

The repair was straight forward; Loosen the screw at the tilt mechanism allowing the burner element to come off the stove and then unscrew two electrical connectors freeing the burned element. The installation could have been as easy as reversing the procedure however the lugs on the new element were poorly placed making it difficult to attach the two halves of the supplied insulator with the clips that secure the two halves. The insulator required the wires to be bent 90 degrees which further complicated the installation. A dremel and some dielectric grease completed the task to my satisfaction. It should have been a 15 minute job. The new element functions far better that the burned element prior to its demise. I should have changed it long ago. I bought the 8" element as a back-up because this stove has only one large burner. However, given my experience with the improvement of the 6", I'll change it shortly. And knowing I may run into the same installation hiccup, I'll prefit the ceramic insulator.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 20