243779-1-S-GE-WB2X9883          -Charcoal Filter
243779-1-S-GE-WB2X9883          -Charcoal Filter 243779-2-S-GE-WB2X9883          -Charcoal Filter 243779-3-S-GE-WB2X9883          -Charcoal Filter

Charcoal Filter

PartSelect Number PS243779

This vent hood filter collects grease particles in the air from cooking. Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $31.52
  • You Save

    $5.25
  • Your Price

    $26.27
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Aluminum Grease Filter

Part Number 255242

This aluminum filter collects grease particles in the air from cooking. Sold individually.

$41.91
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 5 reviews What's this?
1-5 of 5
 

371 of 378 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJean-Christophe from Salisbury MA

Turne table ot moving. Filter never changed

I had no idea what to expect. I was tired to see this turn table not moving. I removed the 7 screws at the bottom of the microwave that I thought was hiding the turn table mechanism. Bingo! I removed the 2 screws holding the motor and check if the power was coming to the motor and it was. The motor was cooked.
I decided to change the filter since I was working on this. When I received it, and proceeded to change it, I found out that there was no filter. Finding the right position was a bit tricky. The most difficult part was to remove the front vent grille.

Don’t be shy, try it! Make sure, to disconnect the power when changing the filter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 24 people found this instruction helpful

Parts Used

  • Charcoal Filter

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerStuart from North Port NY

Replace charcoal filter

Philips head screwdriver to remove 2 screws holding plastic grill above microwave door in place. Old Filter lifts out slide new filter in. It rests on an angle. Re insert Grill (careful that plastic tabs slide into proper slots). Tighten SCrews

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDavid from Dade City FL

Original filter needed replacement, bulb socket was damaged, lens was broken.

Removed the 7 screws holding the bottom of the microwave cover, also opened the access covers to the lights. Damaged socket was easily replaced along with both bulbs and the broken lens, then resecured the covers. Top front cover was removed (2 screws) and the new filter was inserted, then the cover replaced. Very easy, about 15 minutes, without any injuries!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Charcoal Filter

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDavid from Lafayette CO

Grill for exhaust was broken.

Ordered a replacement grill, replaced the optional charcoal filter at the same time. Took just a little effort to get the alignment tabs in place--required just a little more elbow grease than you'd think, then replaced the two screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCami from Roswell GA

Broken turntable motor

This repair was one of the easiest I've ever done. I turned off the power to the microwave at the breaker, lowered the bottom panel by removing the screws, disconnected the wires to the old motor, pulled it out by removing two screws attaching it, attached the new motor with the same screws, connected the wires to it and that was all. The turnable has worked perfectly (and quietly) since.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5