237772-1-S-GE-WB26X10038        -Drive Motor
237772-1-S-GE-WB26X10038        -Drive Motor 237772-2-S-GE-WB26X10038        -Drive Motor 237772-3-S-GE-WB26X10038        -Drive Motor http://www.partselect.com/Schematics/GE/GE_Thumb/00122503i01.gif

Drive Motor

PartSelect Number PS237772

This motor rotates the glass turntable in the microwave and accepts a D-shaped shaft.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Tray won’t turn.
  • Noisy.
  • Won’t turn on.
  • Compare At

    $56.64
  • You Save

    $9.44
  • Your Price

    $47.20
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 155 reviews What's this?
1-5 of 155
 

467 of 483 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerGERRY from BONITA SPRINGS, FL

No water from dispencer

Repairs went just fine done I about 20 min.

Help other customers find the most helpful instructions.

Were these instructions helpful?

377 of 385 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJean-Christophe from Salisbury, MA

Turne table ot moving. Filter never changed

I had no idea what to expect. I was tired to see this turn table not moving. I removed the 7 screws at the bottom of the microwave that I thought was hiding the turn table mechanism. Bingo! I removed the 2 screws holding the motor and check if the power was coming to the motor and it was. The motor was cooked.
I decided to change the filter since I was working on this. When I received it, and proceeded to change it, I found out that there was no filter. Finding the right position was a bit tricky. The most difficult part was to remove the front vent grille.

Don’t be shy, try it! Make sure, to disconnect the power when changing the filter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

368 of 372 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDianne from Westminster, CO

Turntable made a loud noise

First I unscrewed the screws that were holding the panel underneath. Then I removed the panel and removed the screws that held the turntable motor in place. Then replaced the old motor with the new and screwed everything back into place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

148 of 214 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKim from Centerville, GA

The turntable motor went out and was making a horrible sound when I started the microwave

First I unplugged the microwave. :) Then, I removed the 6 screws found underneath the microwave, which allowed the bottom piece to hang down so I could see the turntable motor. I took the two screws out holding the motor in place and pulled the electric connectors off the motor terminals. Then I got the new part from PartSelect.com, replaced the electrical commectors, fit the motor back into the slot it came from (cause the pin has to be seated up in the hole) and replaced the 2 screws holding in the motor. Then I put the bottom metal piece back up and put the 6 screws back in. It was really easy - and I'm a chick! ;)

Help other customers find the most helpful instructions.

Were these instructions helpful?

81 of 85 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCharles from Wall, NJ

Grinding sound when tray turned

Unscrewed bottom plate of microwave and two screws that secured motor. Disconnect wires. Reversed process when installing new motor. Couldn't have been easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 155