237772-1-S-GE-WB26X10038        -Drive Motor
237772-1-S-GE-WB26X10038        -Drive Motor 237772-2-S-GE-WB26X10038        -Drive Motor 237772-3-S-GE-WB26X10038        -Drive Motor

Drive Motor

PartSelect Number PS237772

This motor rotates the glass turntable in the microwave and accepts a D-shaped shaft.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Tray won’t turn.
  • Unusual Noise.
  • Won’t turn on.
  • Compare At

    $47.34
  • You Save

    $7.89
  • Your Price

    $39.45
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 155 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerIna from Horn Lake MS

Motor went out. Glass tray wouldn't rotate any longer

Removed the 6 screws that held the cover below my microwave. Unplugged the part, plugged in the new one and I was done. My part arrived from you just one day after I ordered it! It was my first microwave repair ever, and it couldn't have been easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerLanier from Adairsville GA

Tray turned slow or stopped

Remove the 8 screws in the bottom pan covering the bottom, unpluged the lights and motor plug-ins, slid or pulled the pan forward or to me and removed pan. prized the triange piece which fit into the glass tray to turn it to remove it. removed the two screws which held the motor in place. presto, got the model # off the inside panel and ordered the part on the compiiter, \. arrived in 5 days.
P.S. cleaned everything while I had it apart, toke longer than chancing the part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBrian from Irvine CA

Turntable would not rotate

removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWayne from Mt. Juliet TN

Drive motor dead

This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerwilliam from las vegas NV

Rotary dish tray would not revolve

Dropped the bottom of the microwave,removed the two screws holding the motor in, disconnected the electric wires, reversed the procedure and it worked like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTerrence from Milton FL

Excessive noise while driving the glass tray.

Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSherran from Sun City Center FL

Turntable would not rotate.

First I unplugged microwave oven, then removed the six screws at the bottom of the microwave and lowered the base to expose the small motor. I removed the motor and replaced it with the new one. From inside the oven I pushed the drive shaft back into the new motor, then replaced the bottom with the six screws. I plugged the oven in and tested it. It worked! In less than 15 min. I saved over $220, and I'm a 65 year old Grandma! Thank you, thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customermark from oak lawn IL

G.E. Microwave turn table was loud and not working

I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMichael from Raleigh NC

Microwave food turntable not working

Reviewed the current postings surrounding the problem i was experiencing on your website. Located the 5 phillips head screws on the bottom panel. Removed them letting panel hinge down, removed the motor connector and checked for 21V AC with Volt Meter confirming the motor was not operable. Ordered replacement motor which arrived 3 days later during the holidays. Repeated the panel removal then removed the moter retaining screw and replaced with the received part a perfect matching. All in both panel removals for diagnostics and replacement of the motor took about 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTroy from Zieglerville PA

Replaced drive motor on ge spacemaker microwave

I thought this would be a major project but tured out to be very simple - 7 screws, 10 minutes and done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJohn from Tucson AZ

Turn table motor was noisy and lights were blown

I was very surprised to find that the parts for repair were still available after more than 10 years use. I replaced the bulb light sockets because they had become brittle after 10 years of use. I replaced the wiring harness because it had become discolored at the light socket connection end. The harness still worked but I feel safer having a new one. I also found the GE parts site very easy to navigate and order parts from. Replacement parts were installed by using only a philips head screwdriver and removing/reinstalling 14 screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerElaine from Silver Spring MD

Glass cooking tray not rotating

Removed screws from bottom of microwave. Had to invite my neighbor over to remove one of the screws... he used his impact drill.

Found out that the motor was working fine. It was the brown piece that the glass cooking tray sits on that was broken.

I had removed the glass tray and tried to pull out the brown piece...but, it wouldn't come out and so I assumed that it was intact and thought that the motor wasn't working.

It's great that it's so easy to return parts to PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSheldon from Boca Raton FL

Water over flow killed tray drice moter

Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.

All went well.

From part order to finish was less then five (5) days.

The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKent from Puyallup WA

The drive motor was making a loud, horrible noise.

Simple as could be: unplug the microwave, remove 5 phillips screws to access the motor, remove the 2 phillips screws holding the motor in place, un-clip the motor from it's power supply, and reverse the process; you're done! It took all of 3 minutes to complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJoe from Greensboro NC

Turntable stopped working

First I unpluged the power cord. Then I removed five screws on the bottom panel which will swing down to reveal the turntable motor. I removed the electrical plug from the motor and the two screws that hold the motor in place. Put the new motor in place and align the flat side of the motor shaft with the hole in the bottom of the turntable. Fasten the two screws that hold the motor back in place and reconnect the power plug to the motor. Swing the bottom panel back in place and secure with the five screws. Plug the power cord back in and reset the clock and you are ready to use the microwave.

This was a very simple do-it-yourself repair and information on the partselect website was very helpful. The order and shipping process was simple and fast. Anyone who knows which end of a screwdriver to use should be able to do this repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?