| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerThomas from Stuarts Draft VA
Valve was leaking
very easy to replace. Longest part of the repair was vacumming out the bottom of the refridgerator which I recommend everyone to do.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerLeonard from Leitar NM
Dripping water from despenser
Moved frig away from wall, unpluged and took off lower back panel. Disconnected water line and ice maker lines from water valve (after shutting water off). Removed 2 screws, New valve was exact replacement. With new valve in hand, I removed electrical connecters one at a time and placed them on new valve. Put new valve in place, inserted 2 screws and tightened, Connected water lines, checked for leaks, moved frig back in place, job complete. No more drips, worked perfect. Total time, about 30 min.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Wrench(Adjustable)
CustomerDavid from Wyncote PA
Water kept running and freezing in inlet port
Removed back cover. Removed screws holding it in the rear of freezer. Removed wires. Connected wires to new part, re installed.
Very quick and easy. Ice maker running like new.
(And part was shipped and received almost instantly)
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerGerald from Shawnee KS
Water dispenser valve quit working
Turned water off, Removed back cover. Removed the two electrical connections. Removed the two screws holding the valve. Pulled it out a little ways and disconnected the three water lines with pliers. used shallow pan to catch water. Part was an exact replacement installed in reverse order.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerWALTER from WHISTLER AL
Would not make ice
I HAVE A WATER FITER SYTEM THE ICE MAKER IS SUPPIED FROM. I HAD TO DRAIN SYSTEM TO RELEASE PRESSURE. I THEN REMOVED THE 2 SCREWS SUPPORTING THE VALVE. REMOVED VALVE AS FAR AS WIRES AND SUPPLY LINES WOULD ALLOW AND DISCONNECTED. REPLACED ON NEW VALVE AND REINSTALLED. THIS TURNED OUT NOT TO BE THE ONLY PROBLEM, ICE HAD FORMED DEEP INTO THE SUPPLY TUBE. HAD TO TAKE A HAIR DRIER AND DEFROST THE TUBE UNTIL I COULD BLOW THRU IT. IT IS NOW MAKING ICE.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerWatson from Denton TX
No water through door
I replaced the fill valve by first unplugging the referigerator turning offf the water supply before removing the cover to gain access to the water valve. I removed to bracket from the old fill vale and installed on new valve. Reversed the above and it fixed the problem. I ordered the part from PartSelect for this twenty five year old referigerator and received it the next day. Fastest service ever! Right part too!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Wrench(Adjustable)
CustomerDavid from Pikesville MD
Ice maker did not fill with water and water dispenser ran constantly.
It took me longer to move the refrigerator, vacuum the dust from the floor and rear and remove the back panel than to replace the part. Two screws held the part in place, two plugs and two hoses connected the part. All said and done in 35 minutes I have a refrigerator with a working icemaker and water in the door dispenser. Why did I ever delay so maney months in ordering this part to complete an easy repair job?
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
Tools
CustomerJames from massapequa NY
Waterhose socket leaked- fan didn't work and kick grid was broken
WE FOLLOWED DIRECTIONS AND THANK GOD MY HUSBUND IS A ELECTRICIAN. HE WAS ABLE TO RECONNECT THE WATER-- MAKE THE FAN WORK AND REPLACE THE KICK GRILLE. VERY HAPPY EVERYTHING WORKED.
|
1 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerJim from Gainesville TX
Icemaker supply solenoid did not shut off water flow completely.
After turning off the internal freezer and refrigerator control knobs, I disconnected the power cord. I then removed the lower back cover, the two hex screws holding the inlet valve bracket to the refrigerator frame, disconnected the incoming water line and the two plastic plastic water lines (going to the drinking water spigot and ice maker).
I next marked the two quick-disconnect wiring plugs (for reference on re-assembly). The whole unit came out very easy. I then installed the old mounting bracket on the new water inlet valve, and did reverse installation. Piece of cake.
|