| |
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSusan from Grand Junction CO
Broken control knob for cooktop
found the picture of the piece I needed on your website, ordered it and have it almost immediately. very pleased with the service.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRonald from Sumas WA
Electrode would not spark
removed two screws, lifted the element, disconnected wire, removed one screw that holds electrode, replaced anf assembled
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerThomas from Potomac MD
Ignitors with very weak sparks (2 burners)
Should have read the partselect instructions first 1.) unplugged range 2.) unscrewed (torque screws - good thing I had some) burners - one screw was corroded into the top and snapped - will require a drill to remove and replace metal screw. 3) slid electrical wire from contact 4.) unscrewed (with phillips) Burner Electrode assembly (also corroded - took some force) replaced electrode assy and reversed steps. Works perfect.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
Customerbill from spokane valley WA
Electrode clicked but failed to light burner
I first tried to remove the torx screws only to have them break off..soooo as with most home repairs it grew into a bigger task. 1) unhooked the gas line and unplugged the unit 2) place the unit upside down on workbench 3) used a socket set to remove the hex screws that held the top on 4)removed all the other burners and disconnected electrical wire connected to the igniters. 5) Removed the top 6) uses pliers to remove the screw parts left in the burner base (wd-40 and lock wrench)..Replaced the old gaskets 7) put the top back on and screwed the top back on (make sure you pull the igniter wires through the top before securing it) 8) Reseat and screw in the burners using a torx bit
|
2 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMary from Granite Bay CA
My knob broke
There is really nothing to replace a stove knob. What I was impressed with was the speed in which the knobs came to my house, the very next day from the day I ordered them.
Thanks a ton!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTamara from Crown Point IN
Original knobs were broken. They are only plastic afterall and no did not hold on the stem to turn on and off without duct tape.
Simple. I went online, found the replacement part, ordered 5 new knobs. They came within 4 days and I put them on. Easy as can be. I saved this site so I can go back to it if I ever need to. Wonderful! Thank you..
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Encinitas CA
Melted knobs, replaced
Ordered from Sears.com....under impression that we would get 4 knobs for about 20.00, to our surprise we got only one knob for 20 dollars plus shipping.
Your website was wonderful... have three knobs for the same price as one from Sears.
Thank you.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerSherry from Mentor OH
Knobs on the new jennair range I just purchased started to melt and when they were called they did nothing about it. I had to call and get new knobs at my cost.
Very easy, just removed the old ones and the new ones just clicked on.
|
1 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from Alta Loma CA
Knobs split, was getting inaccurate flame
Remove old knob. Replace with new knob.
|