237580-1-S-GE-WB26K5061         -Upper Cooling Fan Motor with Blade
237580-1-S-GE-WB26K5061         -Upper Cooling Fan Motor with Blade 237580-2-S-GE-WB26K5061         -Upper Cooling Fan Motor with Blade

Upper Cooling Fan Motor with Blade

PartSelect Number PS237580

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $119.94
  • You Save

    $19.99
  • Your Price

    $99.95
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 3 reviews What's this?
1-3 of 3
 

19 of 20 people found this instruction helpful

Parts Used

  • Upper Cooling Fan Motor with Blade

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Socket set

CustomerDavid from Richardson TX

Replace failed fan in control box

After turning off the breaker to cut power to the oven, I opened the oven door and, using the PartSelect exploded diagram as a guide, I removed 3 screws from the underside of the control panel - I was then able to slide the panel up and out to remove it. Leaving all of the control wires (especially the ribbon) connected to control panel, I saw the fan assembly mounted to the rear of the control box.

I noted the position of the two attached wires - black on top (or left), white on bottom (or right). Using a nutdriver with an extension bar, I unscrewed 4 screws holding the assembly in place. I removed the old fan and installed the new fan in its place. It was necessary to bend the new fan's legs out a bit to get them to line up with the holes. I reconnected the wires as mentioned above, then reinstalled the control panel.

I tested the oven by turning the breaker back on and letting the oven heat up to 450 degrees. The fan turned on as expected. After the oven cooled off, I reinstalled the 3 screws to secure the control panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Upper Cooling Fan Motor with Blade

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

Customerlloyd from lorena TX

Lots of fan noise with f2 error code when oven on

Made triple sure electricity off. GE designed excellent access to box above oven. Remove three bolts above oven door on bottom of control panel. Slightly raise panel to take off control panel, let hang by wires. Fan in back wall behind panel and has two wires that unplug, four screws to remove. Plug in new fan, input 4 screws. Partselect excellent guide to make sure correct part was ordered, and very timely delivery. $85.00 part instead of $1500.00 new oven. Tip - Note that fan burns out when auto clean turned on. Stop doing that and problem doesn't repeat.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Upper Cooling Fan Motor with Blade

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsWrench set

CustomerKurt from Novi MI

Oven over heat sensor in upper control compartment going off due to circulation fan failure.

Turn power to oven off at the breaker.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.

Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3