http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33096.gif
See part 4 in the diagram

USE WPL 703650

PartSelect Number PS2375629

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Cooktop element not heating.
  • Will not start.
  • Compare At

    $69.67
  • You Save

    $11.61
  • Your Price

    $58.06
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 53 reviews What's this?
46-53 of 53
 

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customergilbert from san antonio TX

Grill was getting red hot with out control

Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerTim from Lorton VA

Rf burner would not heat

1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerCharles from Bourbon MO

Sparks shot out from under knob, then, no surprise, the burner didn't work

I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!

Now, on to how I did this without fire or electrocution:

Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.

The hardest part was getting the plate to re-seat.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerAmy from Rosebush MI

One of the four burners was not working

Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWilliam from Valley Grande AL

Back burn would turn high no mater where you set the control knob.

Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJames from Dunnellon FL

The 6in burner would go to max heat regardless of the setting.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerPaul from Collegeville PA

Burner only operated on high, no medium or low heat.

First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.

Help other customers find the most helpful instructions.

Were these instructions helpful?

37 of 1320 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerSimon from Federalway WA

Burner swiths two, and radiant element cartridre has been problem in and out for month.

replaced switchs and cartridge, looks like bland new for spending 350 instead of new one for 1500. thank you for the parts i needed it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

46-53 of 53