http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33309.gif
See part 7 in the diagram

USE WPL 703650

PartSelect Number PS2375629

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Cooktop element not heating.
  • Will not start.
  • Compare At

    $64.16
  • You Save

    $10.69
  • Your Price

    $53.47
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 53 reviews What's this?
 

2 of 3 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRandall from Eureka MO

Any setting selected (1 thru 9) would result in the surface burner going to full hot

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customercharles from Newton NH

Grease filter did no fit much to large

switch went well
removed 4 screws and lifed front panal up and out

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerArthur from Cardinal VA

Front element would not turn on

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerScott from Chehalis WA

Burned up switch

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerThomas from Batavia NY

Broken surface burner control

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerDaniel from Temple TX

Burned burner control out of warranty

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerThomas from Batavia NY

Control switch would not operate

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerJerry from Sedro-Woolley WA

Lefrt front burner quit working

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerDaniel from Amherst VA

1.Access panel door strike broken. 2. 8" element operated at high heat only

1. Pressed new door strike into access panel replaced access panel.
2. Turned off power to stove at main power switch panel. Opened access panel and decoupled down draft fan discharge duct. Pulled range out of counter about 3 inches to clear instrument panel side plates. Removed knob from control switch. Removed 4 screws retaining trim at bottom of instrument panel. Removed 4 screws holding instrument panel in place. Lowered instrument panel. Rotated panel top outward to expose surface burner infinite control switches. Checked all connections to suspect control switch with voltmeter to ensure no residual voltages present. Held new switch in same position as installed switch and swapped connections one at a time. Removed two screws holding old switch in panel and removed old switch. Installed new switch in panel using the two screws removed. Re-assembled range in reverse order above and slide back into counter. Recoupled downdraft fan discharge duct and reattached access panel. Reattached conrol switch knob. Restored power to range at main power switch panel. Turned control switch to High until element was red hot. Turned control knob to Low and verified element heat was reduced normally. (Control switch failure was determined by changing stove top elements and experiencing the same high only heating and loss of heat control. A small jar was used to hold all screwa as removed.)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJohn from Bowie MD

One burner only heated to a high temperature.

I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerAnthony from PORTLAND OR

Large burner on cooktop would only operate on high no matter what setting it was at, fan switch did not function

First I located the proper breaker in my electrical panel to turn off the power to the cook top. Then I removed the two screws that hold the housing of the burner knobs and fan switch and lifted it up as much as the attached wires would allow me. To replace the Infinity Control Switch I removed the two "star" head screws from top of housing (under knob) which allowed me to pull the switch off of housing. I pulled off each wire, one at a time, and attached them to the identical place on the new control switch. With all the wires reattached I installed new switch into hole and replaced the 2 screws. To replace the fan switch I removed the 2 nuts on back of housing which allowed me to drop down the switch, swap the wires onto the new switch and place it back onto the bolt posts and reattach the nuts. Finally I turned the breaker back on and tested both new parts to make sure the problems had been corrected. Cook top works perfectly now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerNatalie from North Reading MA

Front burner stayed on high

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerThomas from Discovery Bay CA

Both burner switches failed intrenally

simply remove and replace th switches using a screw driver an a pair of needle nose pliers

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerNorbert from Helotes TX

Left front burner switch was bad. (never shut off heat)

The repair is very easy. Part Select is awesome as far as getting you to the right parts. Just remember that when you do a repair with electricity that you take the time to shut off all possible power sources. I did not and got lucky that I did not injure myself because I did not know the fan switch was also bad. This caused a direct contact with a metal part on the control switch housing while I was disassembling the stove top control. Take your time and think. Should have no problems. Norbert.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • USE WPL 703650

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJames from Charlotte NC

Burner had one temp. Hot

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

Help other customers find the most helpful instructions.

Were these instructions helpful?