This switch allows you to choose which size burner you require according to the size of the pots and pans you're using.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Element will not heat
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Kenmore.
Part# 316239601KIT replaces these:
AP4483961, 1550697, 316239601
Customer Repair Stories
Average Repair Rating: 5.0 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Burner Control switch needed replacing...
The stove is a replacement in a rental. When moving this stove in place, my hand slipped and I hit the control knob for the front burner. It broke the mounting shaft for control itself and therefor the control would just spin when you turned the knob. I ordered a new part that was easy to find and arrived in about 3 days...pretty quick
... Read more. I shut off power to the stove at the breaker and verified the power was off. Pulled the stove out. Removed the top back panel by removing 6 screws (they were the square nut drive type instead of Phillips or slotted). The controller had a single connector attached that was easily removed. I attached the cable to the new controller, place the shaft through the hole in the front plate, used the old nut and washer (the new controller did not come with a nut and washer...lucky I found the old ones) to tighten in place. I then remounted the back panel and replaced the 6 screws, moved the stove back into place and turned the breaker back on. Total time was about 7 minutes. Oh, I had to reset the time on the stove. That was it.
Read less
Peter from North Palm Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
12 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
right front burner would not turn off
pulled the top back cover off, removed knob on front burner control, nut and replaced-Thanks for the prompt service on the part
Ronald from Crescent City, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
8 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brudo
February 4, 2019
My right front duel burner the small burner will not shut off even when the knob is in the off position nor will it temperature control on its own ? Would the burner be bad or is it the switch #316239601 and is there a way of testing that switch ? With a tester.
For model number PLEF398CCC
Hello Brudo, thank you for your question. The most likely issue is the switch itself, as that is the part that regulates the temperature, and sends the signal to the burner to either turn up, or down. We would recommend testing the switch and replacing if necessary. Here is a link that will provide instructions on testing. https://www.partselect.com/Range-Stove-Oven+Infinite-Switch-Testing+repair.htm. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Pete
February 12, 2018
Does this element control switch control the dual element on the right front of the electric range? The dual element is 9 inch 2500w / 6 inch 1000w.
For model number 790.99013102
Hi Pete, Thank you for the question. Yes, this Dual Element Control Switch controls the Dual Element on the right front. Good luck with the repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Stephen
July 28, 2021
Hello,
My front left burner ( burner and bridge element) temperature setting fluctuates it will not stay on a setting. example i set the element to heat at 5.0 and it jumps to 6.0 and down to 4.0 but keeps changing numbers.
what is the part number i need?
thank you
stephen
For model number CPLEF398CCB Frigidaire
Hello Stephen, Thank you for your inquiry. We would recommend checking the burner element and the switch. You can check the parts with a multimeter. Also check the wiring between the element and the switch for any visible damage and wear. Good luck with your repair.
the burner will not turn off the front right dual element I think its the sw.
For model number plef398ccb
Hi Ronald,
Thank you for your question. If the burner will not turn off, you may have either a shorted element or the switch that controls it is malfunctioning. You will need to test the parts with a multimeter for continuity to see which one is causing the issue. To test for a shorted element, touch each of the terminals one at a time with one probe while holding the other probe to the outside surface of the element. If either terminal shows continuity, it is defective. To test the entire element for continuity, place each of the probes on the terminals, one on each. The exact reading you should receive varies between models, refer to your owner’s manual to determine what yours should be, but if any element has a reading outside of 19 to 115 ohms, it is defective. If you do not receive the correct readings from the tests above or find damage on your element, you will need a replacement surface burner element. To test the switch, set your multimeter to the Rx1 setting. Then test for continuity by touching the L1 and H1 terminals with the probes. Once you have completed that test, touch the probes to the L2 & H2 terminals. If your test results indicate that there is no continuity between one or both sets of terminals, you need a replacement infinite switch. We hope this helps! If you have any questions, please let us know.