| |
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerDave W from Granite Bay CA
The upper rack would fall off when pulled out
I installed new rollers and rack clips. The old ones had cracked and would not keep the rack in the tracks. I went to buy a new dishwasher which would have cost around $500. I bought $60 worth of parts although I probably could have just bought the clips for $15 and now the dishwasher is good to go! A real money saver.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRobyn from Spring TX
The end cap for the top rack of the dishwasher broke
We simply followed the example of the end cap on the opposite side and snapped it into place.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerEverett from Lake Elsinore CA
Rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from Meridian ID
Broken rollers on the top rack
Removed the end caps on the rails (push in the retaining clip and pull towards the front), removed the rack from the dishwasher, unclipped the old rollers, assembled the new wheels and retaining clips, installed the new roller assemblies and finally installed new retaining clips for the rails. (bought new clips just in case the old ones did not remove cleanly) Entire repair was too easy. I imagine a serviceman would have charged $75 for that.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerStacy from The Villages FL
End cap broke
The end cap took about 2 minutes to replace. I received my part quickly and installed it really quick and easily.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerHal from Rancho Mirage CA
Bent upper rack slide from tripping accident
My wife grabbed the upper rack as she fell backwards across the front of the open dishwasher. It broke her fall - she is fine thank goodness - but the roller slides broke and the rail was destroyed. The dishwasher repair was easy - just had to put new parts in place. The detail parts explosion helps in determining how all physically goes together. Everything works as good as new. I used the pliers to remove one of the old wheel axles that was attached to the basket.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerRobert from White Stone VA
Wheels on dish rack were falling off due to hard water and water temperature..
Snapped off the old wheels and clips and installed the new wheels. Make sure the wheels are installed on the holder prior to snapping the clip onto the dish rack. Very easy job.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJennifer from Silver Spring MD
Rack end cap was lost or missing
All I had to do was slide the rack forward slightly, reach back to the end of the rack and snap the end cap into place. It helped to have someone there to balance the rack while I was replacing the cap.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
Customersheryl from Washington MI
Spindles on upper dishrack were breaking off
I had to remove the end cap from each side which was a bit tricky but after reading other comments from your website I knew what to do and took my time so that I wouldn't break them. The new upper rack doesn't have the spindles and is a newer design which I really like. It makes the dishwasher seem like new!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
Tools
CustomerCharlene from Nashville TN
Several
THERE IS NOTHING TO TELL I ORDER SEND TO LOCATION AND THEIR MAINTENANCE INSTALLS
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDaniel from Odenton MD
End cap broken
Removal of the old end cap required pliers. Not too difficult. The new end cap simply snapped into place. Both end caps on the two rack slides replaced in less than five minutes.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerGlenn G from Suwanee GA
Upper rollers and axles broke apart
Used needle nose pliers to pop end caps off and remove broken axles. Popped new rollers and axles on rack. Then replaced end caps. Less than 15 min. Easy fix and saved the expense of service call.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDavid from Broomfield CO
Rack slide end cap broke.
I put the new cap in. POC.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerWilliam from Hales Location NH
Top rack rollers broke off
Used screwdriver to pry off old end caps, then slid the rop rack out and replaced the broken rollers with the new rollers. Put the top rack back into dishwasher on its rails and put new end caps on ends of the rails. Job finished! Total time 10 minutes. Easiest repair I've ever had to do!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerallen from grove city PA
Upper rack dificult to rol
removed the end caps and took the rack out of the dish washer.
found right front rack roller bad and replaced.
slide rack back into dishwasher and replace end caps.
|