2370502-1-S-GE-WD12X10304-RACK SLIDE END CAP
2370502-1-S-GE-WD12X10304-RACK SLIDE END CAP 2370502-2-S-GE-WD12X10304-RACK SLIDE END CAP

RACK SLIDE END CAP

PartSelect Number PS2370502

This part attaches to the rails, for the upper rack, to prevent the dishrack from sliding all the way out.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Not cleaning properly.
  • Door latch failed.
  • Compare At

    $.83
  • You Save

    $.14
  • Your Price

    $0.69
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 64 reviews What's this?
1-15 of 64
 

368 of 371 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerJoseph from Haymarket VA

Worn/broken plastic parts were causing misery

Order arrived two days after being placed. Super easy to remove the old, worn, broken plastic parts and replace with new. Everything popped right on just as shown in the diagram. Our happiness with our dishwasher has increased 100%. BTW, thanks to the very helpful, friendly and knowledgeable staff at PartSelect.com -- next job, replace the ice maker in the freezer!

Help other customers find the most helpful instructions.

Were these instructions helpful?

216 of 404 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

Customermichael from perry hall MD

Wheel replacement

Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 22 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerWarren from Stillwater MN

Top and bottom rack were rusted thru

Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 13 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDave from Littleton CO

Parts were old and worn out

The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerPatrick from San Jose CA

Upper and lower racks starting to rust

Removed the lower rack and upper rack after removing the end caps on the rail. Order new replacement end caps. The originals will likely break because the plastic becomes more brittle over time. Unsnap the upper washer arm from the original upper rack and snap onto the new one before inserting it into the rails.

The trick is replacing the end caps. Using needle-nose pliers, bend the indented edge of the rails out so you can attached the new end caps without trouble. After they are in place, use the tip of the needle-nose pliers to restore the indentation on the edge of the rails to lock the caps in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers

CustomerRoger from Simi Valley CA

Broken wheels and attachments

Everything snapped on quite easily. I was releaved to not have to replace "everything."

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • RACK SLIDE END CAP

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerRaymond from ansonia CT

Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray d, ansonia, ct

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Old Lyme CT

2 rollers and end caps were broken were broken

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • RACK SLIDE END CAP

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerJoel from Cypress TX

Upper rack kept dropping from the wheels when we pulled it out

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerROBERT from YOUNGSTOWN OH

Upper tray very difficult to pull out and push in

Using a screwdriver removed upper tray slide end caps.
Removed upper tray.

Removed and replaced upper tray rollers.

Using screwdriver removed track rollers and Track.

Assembled track with rear stops.
Installed lower track rollers.
Holding track in place installed upper track rollers. Installed upper tray and and front track stops.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerTracey from Cedar Hill TX

No ice or water dispencing

I first read about others with the same problem on your web sight and figured if they could do it so could I. Anyway the directions are a little hard to read but it was very informative and straight forward. I took the advice of one of the do it your-selfers when it came down to removing the spring. Be careful not to loose it. Everything was there that I needed and went on without a hitch. Now it was time to see if my repairs were done correctly. Pow! Everything worked. This is a great web-sight to buy parts if you are a do it your selfer. Easy to follow instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDaniel from Circleville OH

Side ends were broken off so rollers came off every time we pulled the racks out

installed new rollers per diagram then installed side ends into sides. Couldn`t have been easier. Dishwasher is like new now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKoosah from Camarillo CA

Rack falling off.

I followed the video instructions on removing the rack slide end cap to prevent breaking it and it was very easy to remove and replace the broken one. I attached the new rack rollers and voila we were back in business. I was about to order a new dishwasher the night before for $5oo! Thankfully the stores website wasn't working so I couldn't. I decided to look online to find out if it was easy just to replace the parts. Looks like I saved close to $500 just replacing those parts! AWESOME!!!!!Thank you for a user friendly website. It made all the difference")

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • RACK SLIDE END CAP

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerCarrell from Cochranville PA

Rack slide end cap missing

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • RACK SLIDE END CAP

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerPaul from Blairs VA

Broken off end caps, top would slide off, frustrating.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 64