Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2367737
NOTE: As per the manufacture, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
1. Unplug unit.2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.3.Slide top back and remove.4. Open door of washer and unscrew 2 screws holding in door lock unit.5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Door lock takes a beating due to flimsy washer door which does not align well and subsequently gets slammed each time which causes lock to malfunction telling the washer that it is not locked. Due to safety the washer will not go into the spin mode. Remove top lid (2 screws) open washer door and loosed the 2 screws holding the lock assembly in place. Reach down into the washer and unsnap the 3 wire harnesses. Reverse to reinstall. Very easy.
Using a screw driver I removed the spring loaded band from around the rubber boot inside the door. You only need to remove the band and then pull the boot from the bottom around to the side. You do not need to fully remove boot. Unscrew locking mechanism. Slide out to be able to see connections. Remove connections. Replace mechanism, reattaching connections into appropriate spots. Replace mechanism and rescrew in. Replace rubber boot by pulling gently out and working rubber V of boot under the metal slot. Once the boot is replaced, replace the metal band making sure the spring is at the bottom of the boot. Wahlah!!! Washer is working perfectly.
Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.Works like new!
Great advice on your site.Repairman "found bad motor control board" and gave me an estimate of $316.00 to repair. I figured that the $80 gamble was worth a shot. Took the top screws off, slid the top back and in less than 15 min. I had a fully functioning washer. Thank you.
took out door lock and switch assembly replace with a new one and it work
this repair was easy, but it was repair #3.#1: Fix-it guy said the front control board needed replaced. Ordered part from box store. Shoulda come here!#2: Replaced motor control board. Harder to replace. Shoulda let the new front board run error code first. Again, used brand name supplier. Oops!#3: Still not spinning. Error code "Door is open" but it's closed.Remove door lock/switch assy, wires to the front board, and striker. 4 screws, 15 minutes. reached in through the top (did NOT unseat rubber around door). Plugged wires into door lock. Inserted striker. Using multimeter on "Ohms" tested switch. No continuity=switch not closed.New switch cost less, arrived faster. thank you Parts Select!
Went on line to your site , found part, read how easy it was for others to repair. So ordered part and replaced myself. I am a woman who's husband is not handy fixing things and it took me no time at all to remove and replace part. Thanks to others who shared how they did in this situation.Much cheaper to repair yourself. You can do it!!
I read the input of others who had this problem with this washer and how they had replaced the door lock and switch assembly. I figured it was worth the $70-$80 part versus the $540 repair or purchasing a new machine. I was really happy with the machine until this problem occurred. When I got the new part.....I unplugged the machine. Took out two screws in the back of the top panel. Removed the top of the machine. Took out two screws in the front of the machine that hold the door lock ans switch assembly into place. I unplugged the three wires from the old part (be careful not to drop the old or new part....if you choose to do this by reaching in from the top like I did for this repair.....easier than removing the entire front of the machine.)I plugged the three wires into the new part and positioned the new part in the door lock position. Replaced the two screws. Put the cover back on the top and replaced the two screws that hold the top cover on the machine. I was thrilled when it worked perfectly. What a relief!Sure glad I looked at this website and tried this! The repairman really didn't know enough about my machine....obviously. I'd like to call him and tell what was really wrong so next time he'll know.
Watched video which was very helpful
I unplugged the washer. Then I unscrewed the two screws on the back, top edge of the washer. and lifted the top off. Next I unscrewed the door lock/switch assembly, reached down in the machine from the top and pulled the switch out. As I unplugged each one of the three plugs from the bad part, I plugged them into the corresponding connections of the good part. Then I screwed the switch back into place, replaced the top of the washer and screwed it back on. I set the washer spin and cheered madly when it went into spin mode. The hardest part was actually turning the screws because I'm a small woman and my hand strength is not what it used to be. But really there was nothing difficult about this repair.
The hardest part was figuring out how to get the lid off. You simply remove two screws from the back of the lid and jerk and slide the lid towards the back of the machine. Take out the screws that hold the front panel on, tilt the front out and access the lock/switch assembly and replace.
Ran diagnostic and discovered that the panel did not recognize that the door was locked, thus no spin. I ordered both parts, although I didn't need the door strike/catch. I only needed the locking mechanism. I removed metal ring from around the rubber piece inside the door with needle nose pliers, and then I simply plugged in the new lock and screwed it in place. I put the ring back around the rubber piece, flipped the circuit back on and washed a load of clothes. Easy as pie! Teachers can do anything. Who needs a repair man? :)
I released the door gasket and unscrewed the unit .Labeled the connections. then reconnected reattached, then put gasket back on. Worked like a charm!
Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new board. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.