Quick Question!

Have you ever purchased from PartSelect.com before?

236754-2-S-GE-WB24T10029        -Surface Burner Switch - 6" - 1560W
236754-2-S-GE-WB24T10029        -Surface Burner Switch - 6" - 1560W 236754-1-S-GE-WB24T10029        -Surface Burner Switch - 6" - 1560W 236754-3-S-GE-WB24T10029        -Surface Burner Switch - 6" - 1560W http://www.partselect.com/Schematics/GE/00115410i01.gif

Surface Burner Switch - 6" - 1560W

PartSelect Number PS236754

This switch controls the small burner on a range/stove top.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Element will not heat.
  • Will Not Start.

Compare At

$30.10

You Save

$5.02

Your Price

$25.08
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Dual Burner Control Switch

Part Number 236780

This switch controls the stove top surface burner.

$37.34
In Stock

Surface Burner Switch - 8" - 2500W

Part Number 236750

$21.90
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 12 reviews What's this?
1-12 of 12
 

63 of 67 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Marc from Columbia, NJ

The switches failed on both front burners.

Remove nobs from both switches.
Pull out the range (the hardest part).
REMOVE THE POWER PLUG FROM THE WALL
Remove 7 screws with nut driver and take off upper back panel.
Remove 2 phillips screws from front, they hold the switch brackets.
The new switches don't fit in the bracket so discard the bracket keeping the screws.
Removing 1 wire at a time from the old switch transfer to the new noting the letter/number ie "H1 P1" combos they are all there just not in the same places on the new switch.
When wiring is complete, using the bracket ,screws from the front screw on the switches.
Replace the back panel with 7 screws.
In my case the old nobs did not fit the shafts of the new switches. I found some at the local hardware store. I bought 4 for $0.29 each! I expect to be replacing the other burner switches shortly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: William from Shenandoah, PA

Back burner not getting hot

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 6 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Thomas from Bonifay, FL

Replace stove top burners (3 total)

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers
Customer: abbas from redmond, WA

Surface burner switch was burned

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: SILVIA from Midlothian, TX

Burner not work

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Anil from Milpitas, CA

Burner spontaneously cycled without knob activation

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 15 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Frank from Glen Cove, NY

Switch went to high setting no matter what the setting was

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: Melvin from Portland, TN

Element blew hole in self then no power to burner.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Deanna from Buckeye, AZ

Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: bryan from cocoa, FL

Burner was inoperative

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 5 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Jack from Greensboro, GA

Burner not heating.

Isolated to control switch.

Replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Surface Burner Switch - 6" - 1560W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: daniel from valentines, VA

Eye wouldnt come on

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-12 of 12