11744611-1-M-Whirlpool-WP7527P023-60-Orifice Holder with Spark Igniter - 5K
Part Location Diagram of WP7527P023-60 Whirlpool Orifice Holder with Spark Igniter - 5K
See part 8 in the diagram
( Grid squares measure 1x1 inch )
11744611-1-S-Whirlpool-WP7527P023-60-Orifice Holder with Spark Igniter - 5K 11744611-2-S-Whirlpool-WP7527P023-60-Orifice Holder with Spark Igniter - 5K 11744611-3-S-Whirlpool-WP7527P023-60-Orifice Holder with Spark Igniter - 5K Part Location Diagram of WP7527P023-60 Whirlpool Orifice Holder with Spark Igniter - 5K
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Orifice Holder with Spark Igniter - 5K WP7527P023-60

Rated by 1 customer 

Difficult 

More than 2 hours 

Ratings submitted by customers like you who bought this part.

$ 72.96
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11744611
Manufacturer Part Number WP7527P023-60
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Range, Cooktop.
This part works with the following products:
Maytag, Jenn-Air, Kenmore.
Part# WP7527P023-60 replaces these:
74007392, 74007816, 7527P023-60
Back to Top
Customer Repair Stories
 Average Repair Rating: 1.5 / 5.0, 1 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Ignitor switches shorted out
The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access.

This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.

1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly.
Read less
Other Parts Used:
Orifice Holder with Spark Igniter - 16K Orifice Holder with Spark Igniter - 5K Spark Igniter Switches and Harness Assembly Orifice Holder with Spark Igniter - 9.2K Torx Screw
  • Michael from Dardanelle, AR
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
39 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Screw
$13.25
$13.25
  In Stock
Orifice Holder with Spark Igniter - 9.2K
$75.88
$75.88
  In Stock
Orifice Holder with Spark Igniter - 16K
$81.04
$81.04
  In Stock
Orifice Holder with Spark Igniter - Right Front
$69.16
$69.16
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744611
Manufacturer Part Number: WP7527P023-60
Brand
Model Number
Description
Kenmore
66578002700
Range
Kenmore
66578002800
Range
Kenmore
66578002801
Range
Kenmore
66578002802
Range
Kenmore
66578002803
Range
Kenmore
66578003700
Range
Kenmore
66578003800
Range
Kenmore
66578003801
Range
Kenmore
66578003802
Range
Kenmore
66578003803
Range
Kenmore
66578003804
Range
Kenmore
66578009700
Range
Kenmore
66578009800
Range
Kenmore
66578009801
Range
Kenmore
66578009802
Range
Kenmore
66578009803
Range
Kenmore
66578009804
Range
Jenn-Air
JDR8895AAB
Range
Jenn-Air
JDR8895AAS
Range
Jenn-Air
JDR8895AAW
Range
Jenn-Air
JDR8895ACB
Range
Jenn-Air
JDR8895ACS
Range
Jenn-Air
JDR8895ACW
Range
Jenn-Air
JDR8895BAB13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BAS13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BAW13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCB13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCS13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JDR8895BCW13
Range - 30" DUEL FUEL RANGE
Jenn-Air
JGR8890ADP
Range
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Orifice Holder with Spark Igniter - 5K
$ 72.96
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.