2365872-1-S-Whirlpool-6-920534-Water Inlet Valve
2365872-1-S-Whirlpool-6-920534-Water Inlet Valve 2365872-2-S-Whirlpool-6-920534-Water Inlet Valve 2365872-3-S-Whirlpool-6-920534-Water Inlet Valve

Water Inlet Valve

PartSelect Number PS2365872

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Will not fill with water.
  • Not cleaning properly.
  • Compare At

    $56.32
  • You Save

    $9.39
  • Your Price

    $46.93
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 5 reviews What's this?
1-5 of 5
 

41 of 42 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerCraig from Old Orchard Beach ME

Broken inlet valve due to freezing - water leak

Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerRobert from Woodstock IL

Weeping water control valve

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerRalph from Taft CA

Very little water going into the dishwasher

Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerLaurie from Cashton WI

Our dishwasher would not take in water. It would partially fill but not to the level required to run properly.

I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set, Wrench(Adjustable)

CustomerValerie from Danbury CT

Dishwasher wouldn't clean dishes

First shut circuit breaker to dishwasher and close water valve under the sink. Remove the screws that hold the dishwasher to the counter, then remove the bottom cover plates. I slid the diswasher out almost all the way...On the left side bottom I could see the old water inlet valve was attached by 2 hex screws and a clip with 3 wires..after removing the 2 screws and clip I was able to remove the water line (place something to catch a small amount of water) and remove the black rubber hose from the old intake valve by squeezing the clip.. Removed the brass nut from the old valve you'll need it. I installed the new water inlet valve by connecting the old brass nut
(replace with new thread seal tape) , replace the water line and black rubber hose...attach to frame with the 2 hex screws and replace clip with wires...I slid the dishwasher back under the counter, turned the water on and power back on...I ran the dishwasher before I secured it in place to check for leaks...Dry as a bone...I then secured it to the counter and replaced the bottom plates.. the dishwasher is working like new...everything comes out spotless...Sometimes repairs are not as hard as they look, just take your time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5