2363196-1-S-Whirlpool-W10250667-Tub Spring
2363196-1-S-Whirlpool-W10250667-Tub Spring http://www.partselect.com/Schematics/Maytag/OGHXSQCE.gif

Tub Spring

PartSelect Number PS2363196

Manufacturer Part Number W10250667
Manufactured by Whirlpool

This part is used to balance the tub during spin cycle. Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shakes and moves.
  • Noisy.
  • Leaking.
  • Compare At

    $4.55
  • You Save

    $.76
  • Your Price

    $3.79
In Stock
Order within the next 34 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 18 reviews What's this?
1-5 of 18
 

646 of 671 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: RICHARD from PHILA, PA

Replace water pump coupling

Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

164 of 181 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Brian from Seattle, WA

Washer tub slammed into washer body during spin cycle

If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.

First I disconnected the washer from the water and power supply, then I laid it on its back.

The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.

Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.

The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.

With $25 in parts and about 15 minutes, my washer spins much more quietly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

66 of 74 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: john from middle river, MD

Machine rocking about like crazy on spin

Took some online research to figure out how to get the cabinet off. Once inside I fitted the wear pads which were a breeze to remove using a knife blade to pry them up and removing them using the screwdriver. The springs were replaced one by one using strong fingers. The machine went through the spin cycle without any rocking or self-destruct noises.

Help other customers find the most helpful instructions.

Were these instructions helpful?

32 of 33 people found this instruction helpful

Parts Used:
  • Tub Spring
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: Lori from Parchment, MI

Sounded out of balance even after shifting clothes

The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not work properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.

Help other customers find the most helpful instructions.

Were these instructions helpful?

29 of 31 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench set
Customer: Michael from Glenburn, ME

Acting like it was unbalanced

I thought I would find broken springs but everything looked good. Comments and video very helpful.I figured springs must be stretched or worn out ,so for the money I figured worth a try. Insallation went well, washingmachine runs like a new machine. Much better than spending money on a new one. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 18