Circulation Pump Motor with Impeller - 60Hz 120V

PartSelect Number PS2363114

Manufacturer Part Number W10239404
Manufactured by Whirlpool

This part has a closed cast motor housing. The sump housing is sold separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not start.
  • Not cleaning properly.
  • Leaking water.
  • Not draining.
  • Will not fill with water.
  • Compare At

    $165.14
  • You Save

    $27.52
  • Your Price

    $137.62
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 28 reviews What's this?
16-28 of 28
 

4 of 4 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set, Wrench(Adjustable)

CustomerDawn from New Richmond WI

Bones inside locked motor up and burned it out

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Socket set, Wrench set

CustomerBrett from North Jackson OH

Pump motor made excessive noise with leaking water

Removed dishwasher from cabinets replaced motor which was easy to do reinstalled in cabinets and ran cycle. All was good. No noise and no leaking.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJOHN from MORA MN

The problem started with the pump getting noisy then it stopped pumping all together there are two pumps in this machine still drained its self.

FIRST RUN THE CANCEL AND DRAIN CYCLE TO EMPTY THE WATER FROM THE MACHINE. NEXT SHUT OFF THE WATER AND POWER TO MACHINE. THEN DISCONECT THE WATER AND DRAIN HOSES, AND UNINSTAL THE MACHINE FROM THE CABNET. THERE ARE USUALY JUST TWO SCREWS AT THE TOP WHEN YOU OPEN THE DOOR. BEFORE YOU TAKE THEM OUT TAKE OUT THE BOTTOM WASH ARM, AND THE SCREAN AND THE COVER OVER THE FOOD CHOPPER. THESE ARE ALL HELD IN WITH STAR SCREWS. AFTER THE COVER IS TAKEN OUT THE CHOPPER WILL LIFT RIGHT OUT.

NEXT LAY THE MACHINE ON ITS SIDE THERE IS JUST ONE CAPSCREW HOLDING THE MOTOR IN LOCATED BEHIND IT WHEN LYING DOWN BUT FIRST UNPUG THE WIRE HARNES TO IT.
THE MOTOR WILL COME OUT WITH JUST A SMALL TWIST AFTER THE CAP SCREW IS OUT.
TO INSTAL JUST TWIST IN PUT IN THE CAP SCREW AND FOLLOW THE DIRECTIONS BACKWARD TILL IT IS INSTALLED AGAIN.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 9 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerPat from San Juan Capistrano CA

Water pump was not functioning.

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Wrench set, Wrench(Adjustable)

CustomerRonald from Duluth GA

Dishwasher making up high pitch noise when running

After looking at what everyone else had done, I decide that I would take the dishwasher out of the wall space and set it on its side. This require me to turn off the power first. Then I pull the diswasher out from its space in the wall. I turned off the the water and then took off the water hose, then took of the return hose. There was water left in both, so there was a little water on the floor as a result of this. Then I finally pulled out the unit and laid it down on its side. The motor was very visible and was easy to access. The hardest part was finding the bolt to take it off. I pulled off the power connector to the motor and then took off the one bolt that was holding the motor on the washer. Then I twisted the motor, but it would not come off. I finally got a screw driver and put it in the small opening between the motor and the connection and it finally came off. This took all of about 30 minutes. Once I got the motor off, I notice that the aluminum grating inside was dirty and needed cleaning. So I cleaned this and put it back inside. The new motor came with every thing, so I put it in and twisted it. Then put back in the bolt, reconnected the power cable, put back on the water and reconnected the output cable. In order to make sure there were no leaks before I put it back in for good, I ran a short wash to check to see if everything was tight. There were no leaks, so I put everything back in the wall. It really did sound very nice now. This dishwasher unit came with noise padding, so I put that back as well. The dishwasher, now is very quite and I don't mind it running any time during the day. The hardest part about this is getting the motor off and find the bolt. It is down between motor and the unit and there was some aluminum between this and the dishwasher, so you need a long nutdriver to get it off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set, Wrench(Adjustable)

Customershane from temple GA

Increasingly loud whirring noise

The machine we bought was one of the quietest. Until recently it would run without making any noise. My wife brought the noise to my attention and I started troubleshooting. I took it apart to find there were pieces of broken glass in the screens and filters. After that I tested it and discovered that the sounds would only come if the motor itself were operating. Replaced motor....bada bing... I look like a hero to the wife.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerDALE from PHOENIX MD

Noisy wash cycle

First of all...do not attempt to change the wash motor from underneath. Pull the dishwasher out of the cabinet and then start following the the mfg repair instructions. It may be probable to replace the motor from underneath, but almost impossible. Helps to turn it over, too. Need star-type wrenches. That being said it was not difficult except to break away the water duct from the sump, kept feeling like something was going to break off. (have to force the duct to the right and it does not want to go far enough to come loose easily)But nothing broke and it's running again. Incidentally, the motor assy or cap was not at fault. Had a bad chopper.
Jim

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerLarry from Georgetown TX

Low "growling" noise, then pump stopped

Ordered a new motor and impeller. Removed old motor when the new part arrived and replaced the part.Very simple repair when placing the dishwasher on its side - must easier than I expected. Great service on part delivery from Partselect! Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerWilliam from Union NJ

Pump/motor seazed.

Shut off circutbraker,shut off hotwater suply.Pulout dishwasher,disconnect wires only.Flip dishwasher onto it's side.Disconnect wireing of the motor.Thereis one screw to take out with a small socket wrench.Than twist the motor/pump counter clockwise and pul out.Place in the new one,turn clockwise,put back plastic shield and screw.Reconnect wireings,reinstall dishwasher,turn power and water back on,test run ,check for leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

Customerjohn from Rogersville TN

Original motor front bearing failed

Removed wash arms inside unit, then removed drain pump and disconnected all wires and took out the 3 clips that hold the assembly in the dishwasher. Everything came out pretty easy and I just put everything back the way it came apart. All told probably an hour with dis-assembly and assembly and no leaks. The motor was perfect, thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerMike from Lake Stevens WA

Grinding noise

I had a grinding noise during the wash cycle. I decided to check the food chopper, all okay there. So I decided to replace the washer pump & motor. When I compaired both the new part and the old part I noticed the tip of the impeller was broken on the new part. I removed the impeller from the old motor and put it on the new one. After I got it back together I tried it and had the same noise. I removed the food chopper and the noise was gone. I guess I'll replace the food chopper now, even though it looks okay.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Circulation Pump Motor with Impeller - 60Hz 120V

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

Customerstanley from laredo TX

Non functioning circulation pump

removed dishwasher from cabinet, unplugged power, leaned dishwasher on it's left side, used a 3/8 nut-driver to remove bolt holding pump, unplugged wiring harness from pump, rotate pump to the left and remove pump. then install new pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 25 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

CustomerStanley from Palatine IL

Frozen motor

I lake to send you pictures
-- Stanley --

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-28 of 28