2363020-1-S-Whirlpool-W10224430-Detergent and Rinse Dispenser with Cap
2363020-1-S-Whirlpool-W10224430-Detergent and Rinse Dispenser with Cap 2363020-2-S-Whirlpool-W10224430-Detergent and Rinse Dispenser with Cap http://www.partselect.com/Schematics/Whirlpool/M5I8MXYF.gif

Detergent and Rinse Dispenser with Cap

PartSelect Number PS2363020

This part releases the detergent and rinse aid into the dishwasher.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not dispense detergent.
  • Door latch failure.
  • Not cleaning dishes properly.
  • Door won’t close.
  • Compare At

    $99.70
  • You Save

    $16.62
  • Your Price

    $83.08
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 7 reviews What's this?
1-5 of 7
 

42 of 47 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Jim from Sherwood, OR

The dispenser door was broken, would not close.

First I removed the (8) screws holding the front door panel on. Then I took the door panel off and unpluged the ribbon wiring so the door was free from the dishwasher. I then unpluded the wiring going to the dispensor. Then I removed the (6) screws holding the dispensor into place and then sprung the holders (2) so the dispendor could be removed. I stuck the new dispensor in its place, pushed it in so the (2) metal holders locked into place, then replaced the (6) screws, pluged the wiring into the new dospensor, pluged the ribbion wiring back in and replaced the front door panel and reinstalled the (8) screws that hold the front door into place. And then tested and everything worked fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 16 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Patrick from Platte City, MO

Latch on soap dispenser failed

I removed the 10 screws that hold the front door panel on and then I removed the 6 screws that hold the dispenser in place, pried slightly on the 2 clamps that hold the dispenser in place, unplugged the wire to it and pulled it out.
Put the new one in and reversed the steps. Presto done!
Works great.
Thanks Parts Select.
PS
Kitchen Aide come up with a better design!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: daniel from corte madera, CA

Soap door latch pin broken

Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Wrench set
Customer: John from Sanibel, FL

The soap dispenser door latch was broken

I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Mike from Redmond, OR

Soap dispensor door was warped

The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 7