| |
15 of 26 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver
CustomerChauncey from Menan ID
Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,
I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine.
|
7 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBruce from Glen mills PA
Broke tab that holds pantry lid; something fell on the pantry lid and cracked the clear section of lid
The parts arrived VERY quickly.Replacement was extremely easy even though the right side end cap has the temperature adjustment it only took 15-20 minutes.
|
5 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerThomas from Webster NY
Broken right hinge
Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDarrell from Yakima WA
Chef's pantry lid was cracked
A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsSocket set
CustomerMichael from potomac MD
Broken nipple/hungry kids
Took bottom 2 shelves out. 2 screws held assembly in to main cabin. Remove them then 2 additional screws held drawer bracket in place. Easy yet patience and finesse is needed
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMaria from Cream Ridge NJ
Chef drawer cover
take the old one out replace with new once - no instructions required, no tools needed
|
3 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerThanh from Anaheim CA
Ice maker making large block of ice, level broken, pantry cover broken
Pantry Cover:
I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.
Ice Maker:
I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), slide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
Customerjoel from reynoldsburg OH
Broken end cap on pantry shelf
remove the three screws which holds the end cap in place. transfer the track to the new part and the temperature control. replace the three screws. very easy!
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerBarbara from East Islip NY
Broken side piece on slide out drawer
It was very easy to replace the broken piece. My husband did it in about 15 minutes .
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers
CustomerBarbara from Branford CT
Right side end cap and pantry lid broken
Removed pantry lid,pantry drawer, shelf, two drawers. Unscrewed metal side rail. Removed right side end cap plus attached back rail. Had to figure out how to remove sliding drawer mechanism, not easy, all plastic, easily breakable-reattached that to new right side end cap. Put everything back (not easy-angle makes it hard). Reattached lid to new side end cap and all is well! My husband and I did this-for us it took two people.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers, Socket set
CustomerJeanne from Fairport NY
The large, sliding drawer, mid-fridge, had a broken part
Actually, my daughter---who is much more mechanically-minded than I---did it. We had to borrow the socket set from a friend. It was relatively simple to do. Of course, the 'fix' led to needing to clean the 'fridge, so that really took the most effort!
Important to note here: THE QUICK RESPONSE OF PARTSELECT IN GETTING THE PARTS TO ME QUICKLY WAS AMAZING!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerThomas from Manassas VA
See through lid separated from lid frame
pulled one side loose than the other. did the opposite to install new lid
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerJenni from Redding CA
My son dropped a mayonnaise jar and broke the lid and bracket.
Using a socket set, I disassembled the old bracket (after removing the shelves and other framework). There were only five screws to remove, and the new brace fit perfectly into place. I had the new bracket on in minutes, with shelves replaced and the new lid snapped into its location. It looked brand new! The appliance repair shop was going to charge me $60 an hour to do the job, not including their mark-up for parts.
|